- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
BANDSAW BLADE: 3450 X 13 X 6TPI CB (WOOD)
SKU:
BSB991184
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3550 X 20 X 4TPI CV (WOOD)
SKU:
BSB991190
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3935 X 20 X 8TPI CB W(OOD)
SKU:
BSB991194
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 4020 X 25 X 6TPI CB (WOOD)
SKU:
BSB991198
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 4790 x 27 x Scallop x 035 Bimetal Hard
SKU:
BSB991203
BANDSAW BLADE: 2375 X 6 X 4TPI CB (WOOD)
SKU:
BSB991205
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2350 X 20 X 8TPI CB (WOOD)
SKU:
BSB991209
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2375 X 10 X 8TPI CB (WOOD)
SKU:
BSB991210
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2375 X 10 X 14TPI CB (WOOD)
SKU:
BSB991216
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2375 X 10 X 18TPI CB (WOOD)
SKU:
BSB991220
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2375 X 3/8 X18TPI CB (WOOD)
SKU:
BSB991224
*Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 2400 x 12 x 4TPI CARBON
SKU:
BSB991230
BANDSAW BLADE: 3300 X 6 X 8TPI CB (WOOD)
SKU:
BSB991260
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3300 X 19 X 10TPI CB (WOOD)
SKU:
BSB991262
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3860 X 19 X 24TPI CB (WOOD)
SKU:
BSB991266
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3855 X 19 X 4 TPI Bi-metal (WOOD)
SKU:
BSB991268
* Carbon blades are the economical choice for general purpose and utility sawing operations.
* These blades cut a wide variety of materials from carbon steels and aluminum to abrasive materials like fiberglass and wood
* For Metal: Bandsaw blades normally get dull from use, but some precautions will give you longer than normal wear on the blades. Blades will dull quickly if used at too rapid a speed for the metal being cut. Also, if the metal to be cut is too hard for the pitch of the blade, you will experience abnormal wear
* The most common cause of premature blade wear comes from using too fine a pitch blade and from feeding the blade too heavy
* For Wood: Proper tracking of the blade is crucial to accurate cutting and considerably reduces blade breakage. The first step to ensuring good tracking is to check that the two band wheels are co-planar. This can be done by placing a straightedge across the front of the wheels and adjusting until each wheel touches. Rotate the wheels with the blade in position and properly tensioned and check that the tracking is correct. Now install the blade guide rollers and leave a gap of about 1 mm between the back of the blade and the guide flange. The teeth of blades that have become narrow through repeated sharpening will foul the front edge of the guide rollers due to their kerf set and force the blade out of alignment. This can be remedied by cutting of a small step on the rollers' front edges to accommodate the protruding teeth. Ideally the rollers should be crowned, a configuration that assists in the proper tracking of bands and belts, at the same time allowing clearance for the set of the teeth
* Carbon blades are more flexible than bi-metal and suit contour work in wood *
BANDSAW BLADE: 3430 X 10 X 4TPI
SKU:
BSB991275
BANDSAW BLADE: 3660 X 25 X 3TPI SIMONDS USA
SKU:
BSB991280
BANDSAW: 12″ DELUX 550W W/STAND TANNER
SKU:
BSW964114
* The Tanner delux bandsaw comes complete with stand
* Fitted with blade guides top and bottom for blade alighnment
* Cast table with mitre gauge slot
* Comes with 550w single phase motor
* Sliding rip fence with graduated rail for easy setting
* Positive single lever action locking for fence
* Comes complete with mitre gauge
BANDSAW: 14″ DELUX 1HP 1PH W/STAND TANNER
SKU:
BSW964116
* Heavy duty Tanner 14" wood bandsaw
* Comes with two speed steps for different materials
* Powerful 1hp single phase motor
* Cast Iron table with slot for mitre gauge
* Easy slide fence with aluminum guideway and single leaver quick locking devise
* Fitted with roller bearing blade guides both top and bottom fpr accurate repetive cutting without distorsion - these guides are adfustable if required
* Comes complete with stand
BANDSAW: 15″ DELUX 1.4KW 1PH W/STAND TANNER
SKU:
BSW964117
* Tanner 15" wood bandsaw
* Comes with two speed steps for different materials
* Powerful 1hp single phase motor
* Cast Iron table with slot for mitre gauge
* Easy slide fence with aluminum guideway and single leaver quick locking devise
* Fitted with roller bearing blade guides both top and bottom fpr accurate repetive cutting without distorsion - these guides are adfustable if required
* Comes complete with stand
* CE standard
BANDSAW: 18″ METAL/WOOD TANNER
SKU:
BSW964118
* This Dayton 18" is a versitile metal and wood cutting bandsaw
* The 18 cast iron wheels are balanced and come with rubber tread
* Blade widths from 3/8 to 1 can be run on this machine
* Fitted with convenient tension and tracking system make blade changing a quick and easy operation
* Come with rip fence and mitre gauge
BANDSAW: 18″ METAL/WOOD 6 SPEED METAL / 1 SPEED WOOD
SKU:
BSW964119
* This Dayton 18" is a versitile metal and wood cutting bandsaw
* The 18 cast iron wheels are balanced and come with rubber tread
* Blade widths from 3/8" to 1" can be run on this machine
* Has six spped changes for metal and one for wood
* Fitted with convenient tension and tracking system make blade changing a quick and easy operation
* Come with rip fence and mitre gauge
BANDSAW: 18″ DELUX 1PH 2200W MOTOR TANNER
SKU:
BSW964120
* This is the Tanner Delux 18" bandsaw
* Arc shape doors for modern appearance
* Quick clamping lever and blade tension adjustment on the back of the
machine.
* Cast aluminum upper & lower wheels fitted as standard
* Two windows to show the saw blade tension and running position
* Parallel fence with micro adjustment function and double reading by magnifier to position 2 sides of the blade of saw and so adapt itself to all the cuttings.
* Additional fence for thin piece facilitates you the access and the
holding of your pieces of small width.
BANDSAW: 28″ DELUX 4HP 3 PHASE TANNER
SKU:
BSW964125
* This is the Tanner 28" wood bandsaw
* Cast iron upper and lower wheels with braking motor fitted for prefect
working performance
* Parallel fence with micro adjustment function and double reading by
magnifier to position 2 sides of the blade of saw and so adapt itself to all
the cuttings.
* Two windows to show the saw blade tension and running position
* Big size working table area 1100 x 700mm totally for perfect
performance.
* Arc shape doors for modern appearance
* Additional fence for thin piece facilitates you the access and the
holding of your pieces of small width.
* Quick clamping lever and blade tension adjustment on the back of the machine.
BANDSAW: 27″ DELUX 3PH 4000W MOTOR
SKU:
BSW964140
BANDSAW: 22″ DELUX 3PH 3000W MOTOR
SKU:
BSW964320
* The MJS550N 22" bandsaw with new slope shape frame
* Precise and simple adjustemnt of the cutting height by means of a handwheel and rack system
* Smooth and flexible allowing 45 deg tilt the work table
* Fitted with roller bearing blade guides both top and bottom
* Positive locking system for fence which slides freely in the aluminum guide system
BANDSAW: STAND MOBILE 14″
SKU:
BSW964600
JOINTER: TANNER MB502 6″ 1 PHASE
SKU:
BZ-330120
JOINTER: TANNER TPC-6 6″ 1 PH TABLE 1535MM
SKU:
BZ-330130
JOINTER: TANNER TPC-6 6″ 1 PH TABLE 1210MM O/STAND
SKU:
BZ-330134
* The W0109 is the standard 6" jointer in the Tanner range
* Closed in stand
* Fitted with the English guard (Not shown in this photo )
* Infeed table features cast-iron support ledge for rabbeting operations
* Fence size 98 x 740mm
* Fence tilt to 45 degrees
* Rebate 13 x 152mm
* Fitted with no-volt overload switch
JOINTER: TANNER TPC-6 6″ 1 PH TABLE 1210MM C
SKU:
BZ-330136
* This TPC-6 comes with powerful 1hp motor.
* Cutterhead is 65mm in diameter.
* Fitted with three knives and runs at 4,400rpm to ensure a smooth finish on the workpiece.
* The fence is equiped with a tilt scale which is clear and easy to read.
*Fence can be tilted to 45° in both directions.
* Fully enclosed delux stand with built-in dust connecter for easy hook-up.
* The machine comes with English type sliding guard.
* Castor wheels for mobility.
JOINTER: TANNER TPC-6 6″ 1 PH TABLE 1535MM
SKU:
BZ-330138
* This W0106F Tanner jointer is the profecional model
* Extra long table (1535mm) for finish accuracy of the workpiece
* Upstand controls for easy operation
* Delux closed in stand
* Dust chute with 4" dust port for efficient dust and chip extraction
* Fence size 124 x 889mm
* Fence tilt to 45 degrees
* Fitted with english type guard ( not shown in this photo )
* Rebate cap i13 x 152mm
JOINTER: TANNER TPC-8 8″ 1PH TABLE 1832MM
SKU:
BZ-330140
* This Professional model 8" jointer comes with a powerful 2hp single phase motor
* Large 1800mm table
* Four knife cutterhead running at 4800rpm to give a smooth finish to the workpiece
* The fence is adjusted by rack and pinion for accuracy and speed
* Fence can be tilted to 45 degrees in both directions
* Fully enclosed steel cabinet with dust connecter built-in
* Comes with English sliding guard (not shown in picture)
* Controls are on a central mount for convenience and safety
* Infeed table is adjusted by leaver action
JOINTER: TANNER TPC-8 8″ 2HP TABLE 1930MM
SKU:
BZ-330145
* This Professional model 8" jointer comes with a powerful 2hp single phase motor
* Large 1930mm table
* Four knife cutterhead running at 4800rpm to give a smooth finish to the workpiece
* The fence is adjusted by rack and pinion for accuracy and speed
* Can be tilted to 45 degrees in both directions
* Fully enclosed steel cabinet with dust connecter built-in
* Comes with English sliding guard
* Controls are on a central mount for convenience and safety
JOINTER: TANNER TPC-8 8″ 1PH TABLE 1340MM C
SKU:
BZ-330150
* This TPC-8 comes with powerful 2hp motor.
* Cutterhead is 65mm in diameter.
* Fitted with three knives and runs at 4,400rpm to ensure a smooth finish on the workpiece.
* The fence is equiped with a tilt scale which is clear and easy to read.
*Fence can be tilted to 45° in both directions.
* Fully enclosed delux stand with built-in dust connecter for easy hook-up.
* The machine comes with English type sliding guard.
* Castor wheels for mobility.
JOINTER: TANNER TPC-12 12″ 1PH 3HP TABLE 2110MM
SKU:
BZ-331400
* The Tanner W0101 jointer is a heavy constructed machine
* Comes with rack and pinion fence adjustment
* The fence is 1200mm long with positive stops on 90 degrees and 45 degrees
* Fence can tilti both in and out
* The heavy all steel cabinet offers the machine stability and rigidity
* The price represents very good value for this size machine
* Conveniently positioned magnetic switch is placed high above the table in full operator view for quick access
JOINTER: TANNER TPC-12 12″ 3HP 3PH TABLE 2110MM
SKU:
BZ-331410
* The TPC-12-3 is a heavy constructed machine with lever action for table rise and fall
* The fence is 1200mm long with positive stops on 90ø and 45ø tilting both in and out
* The heavy all steel cabinet offers the machine stability and rigidity
* The price represents very good value for this size machine
JOINTER: TANNER MB-523 12″ 3HP 3PH TABLE 2000MM S/HEAD
SKU:
BZ-331412
* The MB-523 is a heavy constructed machine with lever action for table rise and fall
* The fence is 1200mm long with positive stops on 90ø and 45ø tilting both in and out
* The heavy all steel cabinet offers the machine stability and rigidity
* Fitted with english type guard
* The price represents very good value for this size machine
JOINTER: TANNER MB-524 16″ 3HP 3KW TABLE 2500MM S/HEAD
SKU:
BZ-331416
* The MB-524 is a heavy constructed machine with lever action for table rise and fall
* The fence is 1200mm long with positive stops on 90ø and 45ø tilting both in and out
* The heavy all steel cabinet offers the machine stability and rigidity
* Fitted with english type guard
* The price represents very good value for this size machine
JOINTER: TANNER MB-524M 16″ 3HP 3KW TABLE 2500MM S/HEAD
SKU:
BZ-331420
* The MB-524 is a heavy constructed machine with lever action for table rise and fall
* The fence is 1200mm long with positive stops on 90ø and 45ø tilting both in and out
* The heavy all steel cabinet offers the machine stability and rigidity
* Fitted with english type guard
* The price represents very good value for this size machine
SPIRAL CUTTER HEAD: 8″ MODEL WITH CARBIDE INSERTS
SKU:
BZ-331520
SPIRAL CUTTER HEAD: 12″ MODEL WITH CARBIDE INSERTS
SKU:
BZ-331530
CHISEL MORTICER: HOLLOW CT1913
SKU:
CM-100000
* The CT-1913 is a quality engineered cost effective machine
* Has a big capacity of up to 25mm mortises
* The heavy cast-iron construction of the column table base and cross slide provides maximum stability
* Specially designed for precise trouble free and long life operations special attention has been paid to health and safety regulations
* This machine will provide excellent morticing results when applied in woodworking plants to manufacture furniture sashes and doors...etc
CHISEL MORTICER: MS3840
SKU:
CM-100020
CHISEL MORTIC BITS: 6PC SET
SKU:
CM-100050
CHISEL MORTIC BITS: 6PC SET
SKU:
CM-100050
CUT OFF SAW: AIR CS-18 R/H UP-CUT
SKU:
COS336600
* This CS-18 Upcut saw is manufactured in Taiwan
* Ideal saw for pre-cut yard or volume cutting
* Foot control to allow hands free cutting
* Safety guard clamps over the workpiece before blade comes up
* Comes complete with TCT 18" blade
* This is a right hand model - also available in left hand
* ( picture is showing the left hand model )
OUTFEED TABLE: CFS-18 2500MM
SKU:
COS336810
DOWEL BORER: BM-301B 2HP 1PH
SKU:
DB-342450
* This a ideal machine for repitition boring
* Heavy cast construction in table and machine frame
* Table is slotted for mitre gauge
* Overhead air clamping comes standard with this machine
* Boring and clamping opperation is controlled by foot pedal allowing the hands to be free to handle the workpiece
* Two heavy bar sections allow the drilling head to advance into the workpiece in a smooth and controled movement
* A large range of drilling heads are available
DISC SANDER: DS-20 20″ 1PH
SKU:
DCS501100
DISC SANDER: DS-12 12″ 550W 1PH TANNER
SKU:
DCS501120
* Compact disc sander with tilting table to 45ø
* Built in dust chute 63mm dia
* Single phase machine with 550w motor
* Ideal home workshop
* Stand is available for this machine
* Safety guard for sanding disc
* Velcro backing on disc for quick paper changing
* This machine has solid cast iron table with mitre gauge
DISC/BELT SANDER: 12″ DISC 150 X 1220MM BELT 1.1KW 1PH
SKU:
DCS501130
* Compact disc and belt sander with tilting table to 45ø
* Belt sanding attachment can be used hoizontal or in a vertical position
* Built in dust chute 40mm dia
* Single phase machine with 1.1kw motor
* Ideal home workshop
* Comes with open type stand
* Safety guard for sanding disc
* This machine has solid cast iron table with mitre gauge
* Belts are available in serveral grits as required
DUST EXTRACTOR: CT-50W WALL MOUNT 1HP 1 PHASE
SKU:
DE-100080
* Small wall mounted dust extraction unit
* Perfect for small worksops or home garage
* Space saving when space is a prenium
* Fitted with 1 micron canister for catching that fine dust
* East cleaning by turning the front mounted handle
* Chips and dust will drop into the bag for easy disposal
* Intake poert 100mm diameter
DUST EXTRACTOR: FM-230 MINI 1HP 1 PHASE
SKU:
DE-100100
DUST EXTRACTOR: FM-300 2HP 1PH 1200CFM
SKU:
DE-100120
DUST EXTRACTOR: FM300S 3HP 1PH 2200CFM
SKU:
DE-100130
DUST EXTRACTOR: FM300S-3HP 3PH 2300CFM
SKU:
DE-100135
DUST EXTRACTOR: FM-500S 5HP 3PH 2500CFM
SKU:
DE-100140
DUST EXTRACTOR: CT-202 5HP 3PH 2120CFM
SKU:
DE-110044
DUST EXTRACTOR: CT-502 2HP 3PH (METAL GRINDINGS)
SKU:
DE-110054
DUST EXTRACTOR: CT-402HS 10HP 3PH
SKU:
DE-110056
AIR FILTRATION UNIT: CTI-500 510CFM
SKU:
DE-110062
* Ceiling hanging model with remote control.
* Removes 98% of airborne contaminates.
* Double filter design is easy to change
* Pre-Filter 5 micron - Final filter 1 micron
* No outside venting required.
* Can be run night and day.
* Can service up to 20 x 20 room with 10 times air cylcle
* Comes with 3 speed settings and built in timer that can be set at 2, 4, 6 and 8 hour increments.
AIR FILTRATION UNIT: CTI-1400 1400CFM
SKU:
DE-110064
* Ceiling hanging model with remote control.
* Removes 98% of airborne contaminates.
* Double filter design is easy to change
* Pre-Filter 5 micron - Final filter 1 micron
* No outside venting required.
* Can be run night and day.
* Can service up to 4000sq ft room.
* Comes with 3 speed settings and built in timer that can be set at 2, 4, 6 and 8 hour increments.
VACCUM CLEANER: ELSEA VIBRA WPB250EA 77 LITRES
SKU:
DE-110071
* Elsea vacuum cleaners are manufactured in Italy.
* Ideal for comercial cleaning or hooked up to powertools as a dust extraction unit.
* This is a two stage cleaner with two motors to provide maximum sucking power.
* This model is equiped with a microprocessor which allows automatic start/stop when using power/air tools when plugged into this machine.
CYCLONE: T-3000CK-C1 3HP MOTOR 1PH
SKU:
DE-110105
* Mobile cyclone dust extractor, suitable for small to medium sized workshops.
* Able to connect to two machines using the 2 x 100mm adaptor.
* Well built units with a steel impeller.
* Nice and quiet operation.
* Automatic filter cleaning for consistent airflow.
* A manometer gives a quick, visual indication of performance.
* Wheeled waste bin, makes the task of waste disposal easier.
* All round extractor, able to cope with all but the largest machines.
CYCLONE: DE-3100ECK 3HP 3PH
SKU:
DE-110110
* This cyclone is suitable for most medium size workshops.
* The 2200cfm capacity allows for good dust collection under all conditions.
* No clogging of filter - waste collected before it gets to the filter.
* Large filter surface area.
* Filters down to 1 micron.
* Small footprint.
* Collection drum is on wheels - making disposal of sawdust and waste easy.
* Mobile castor base allows you to get the machine in just the right spot.
CYCLONE: DE-25SECK TWO STAGE
SKU:
DE-110115
* Mobile cyclone dust extractor, suitable for small to medium sized workshops.
* Able to connect to four machines using the 4 x 100mm adaptor
* Well built units with a steel impeller.
* Nice and quiet operation
* Automatic filter cleaning for consistent airflow.
* A manometer gives a quick, visual indication of performance.
* Wheeled waste bin, makes the task of waste disposal easier.
* All round extractor, able to cope with all but the largest machines
* Supplied with remote control
CYCLONE: CT-25SDC 5HP 3PH
SKU:
DE-110140
CYCLONE: T-3000CK-H 2 STAGE 3HP
SKU:
DE-110350
This T-3000CK-H cyclone has exceptional perfprmance on both fine dust and chips
* Ease of mobility with special design castors
* Automatic filter cleaning for consistant performance
* Filter cartridge captures 99% of dust 0.20-2 microns in size
* Negative pressure in the drum design creates a vacuum between plastic bag & drum
* Remote control for convenient operation from virtually anyware in the shop
* This is a two stage high performance cyclone
CYCLONE: T-5000CK-H 5HP 2 STAGE 3 PHASE
SKU:
DE-110352
This T-5000CK-C2 cyclone has exceptional perfprmance on both fine dust and chips
* Ease of mobility with special design castors
* Automatic filter cleaning for consistant performance
* Filter cartridge captures 99% of dust 0.20-2 microns in size
* Negative pressure in the drum design creates a vacuum between plastic bag & drum
* Remote control for convenient operation from virtually anyware in the shop
* This is a two stage high performance cyclone
