- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
DUST BAG: 360 X 800 5 MICRON
SKU:
DEA110086
DUST BAG: 500 X 800MM CLOTH TOP
SKU:
DEA110090
DUST BAG: 500 X 1200MM CLOTH BOTTOM
SKU:
DEA110092
DUST BAG: 600 X 800MM BOTTOM CLOTH 5 MICRON
SKU:
DEA110134
PLEATED FILTER: 500 x 1000MM 3 MICRON
SKU:
DEA110200
* Pleated filters are designed to replace the conventional upper dust bag on dust extraction units * These canisters filter particles as small as 2 microns where a standard cloth bag filters down to 30 microns * To clean this filter you simply turn the top handle to rotate the cleaning flappers inside * This shakes the dust from the pleating letting it fall into the bottom collection bag * This filter will fit all dust extractors with a neck diameter of 500mm *
PLEATED FILTER: 370 X 600MM
SKU:
DEA110208
* Pleated cartridge filters are far more efficient than filter bags, rated to 1 micron
* Will also suit many other brands of 2HP and twin bag extractors with a drum size of 480mm,
* The unit is cleaned by rotating the handles several times, doing this rotates a rubber beater inside that removes settled dust from the pleats.
PLEATED FILTER: 370 X 1000MM
SKU:
DEA110209
* Pleated cartridge filters are far more efficient than filter bags, rated to 1 micron
* Will also suit many other brands of 2HP and twin bag extractors with a drum size of 480mm,
* The unit is cleaned by rotating the handles several times, doing this rotates a rubber beater inside that removes settled dust from the pleats.
PLEATED FILTER: 500 X 600MM 1 MICRON
SKU:
DEA110210
* Pleated cartridge filters are far more efficient than filter bags, rated to 1 micron
* Will also suit many other brands of 2HP and twin bag extractors with a drum size of 480mm,
* The unit is cleaned by rotating the handles several times, doing this rotates a rubber beater inside that removes settled dust from the pleats.
PLEATED FILTER: 500 X 610MM
SKU:
DEA110230
* Pleated cartridge filters are far more efficient than filter bags, rated to 1 micron
* Will also suit many other brands of 2HP and twin bag extractors with a drum size of 480mm,
* The unit is cleaned by rotating the handles several times, doing this rotates a rubber beater inside that removes settled dust from the pleats.
PLEATED FILTER: 500 X 1220MM 1 MICRON
SKU:
DEA110245
* Pleated cartridge filters are far more efficient than filter bags, rated to 1 micron
* Will also suit many other brands of 2HP and twin bag extractors with a drum size of 480mm,
* The unit is cleaned by rotating the handles several times, doing this rotates a rubber beater inside that removes settled dust from the pleats.
FLOOR SWEEPER: CT-31 NEW TYPE
SKU:
DEA120296
FLOOR SWEEPER: CT-30
SKU:
DEA120298
EDGE SANDER: BS6 X 100-1 BELT: 152 X 2515.
SKU:
EDS241240
* Built to offer a smooth and reliable sanding performance
* The CT-108 will enable you to produce a quality fine edge finishing efficiently
* Featuring a powerful 3hp 1ph motor
* The CT-108 is equipped with a 7" diameter drive pulley and a 3 diameter idler pulley
* Both precision machined and dynamically balanced
* Both front and side tables are made from wood to prevent scratching the workpiece
EDGE SANDER: ES-689 E/TABLE
SKU:
EDS241280
* This sander will sand both vertical and horizontal position or any angle between 0 - 90deg
* Belt platen is made from precision ground steel
* Each end of the belt has a dust port for efficent dust collection
* The front cast iron table can be moved up and down as well as in and out
* Main sanding belt runs in precision ball bearings and is oscillated by a heavy duty worm and gear mechanism which is run in an oil bath
EDGE SANDER: ES-6108
SKU:
EDS241288
* Sanding belt can be used in a vertical or horizontal posistion or any angle between 0 - 90ø
* Belt platern is made from from precision ground steel
* On each end of the belt is a dust port for efficent dust collection
* The cast iron table can be moved up and down as well as back and forward
* Main sanding belt runs in precision ball bearings and is oscillated by a heavy duty worm and gear mechanism and runs in a oil bath
EDGE SANDER: MGD-120ED 5HP
SKU:
EDS241320
* Heavy duty edge sander
* This newly designed belt oscillation system is combined with the main motor and gear system * A powerful drive motor for efficient mass production
* Tables will tilt to 45ø and the height can be adjusted
* Belt change is a single lever action for rapid belt changing
* Both drums are rubber coated and balanced for smooth opperation
* The machine is equipped with a end table for curved sanding and two large tables for edge sanding
EDGE SANDER: TANNER W503 BELT 2260 X 152MM 1.5HP
SKU:
EDS241330
* The TANNER W0503 is a Heavy duty edge sander
* This newly designed belt oscillation system is combined with the main motor and gear system
* A powerful drive motor for efficient mass production
* Tables will tilt to 45ø and the height can be adjusted
* Belt change is a single lever action for rapid belt changing
* Both drums are rubber coated and balanced for smooth opperation
* The machine is equipped with a end table for curved sanding and two large tables for edge sanding