- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
UNIVERSAL JOINT: KOKEN 3/4″ DR
SKU:
SSK6770
* Koken tools are manufactured to strict quality standards and each item is carefully checked before it leaves the factory * Any tool which fails because of defective mateial or workmanship will be repaired or replaced under warranty * Made in Japan Koken tools have a reputation through-out the world for their fine quality and reliability * Choice of tradesmen in industry as well as the home user *
ADAPTOR: KOKEN 1″ DR F X 3/4″M
SKU:
SSK8866A
* Koken tools are manufactured to strict quality standards and each item is carefully checked before it leaves the factory * Any tool which fails because of defective mateial or workmanship will be repaired or replaced under warranty * Made in Japan Koken tools have a reputation through-out the world for their fine quality and reliability * Choice of tradesmen in industry as well as the home user *
TORX SOCKET SET: KOKEN 1/2″ DR T20 – T60 ON RAIL
SKU:
SSKRS4025-9
* Koken tools are manufactured to strict quality standards and each item is carefully checked before it leaves the factory * Any tool which fails because of defective mateial or workmanship will be repaired or replaced under warranty * Made in Japan Koken tools have a reputation through-out the world for their fine quality and reliability * Choice of tradesmen in industry as well as the home user *
KNIFE BLADE: STANLEY SNAP
SKU:
ST-113000
KNIFE BLADE: STANLEY SNAP 10PC
SKU:
ST-113010
SAW MULTICUT: STANLEY 15-275C
SKU:
ST-152750
SAW: TENON/MITRE STANLEY 14HT
SKU:
ST-153520
CHISEL: STANLEY 18MM BUTT
SKU:
ST-166150
* Stanley chisels have been preferred by tradespeople for decades * Blades are hot forged hardened tempered then ground to a fine finish * Blades are made from high carbon alloy steel * Handles are tough cellulose acetate butyrate * Contractor grade butt chisels feature a short bevelled blade and handle is fitted with a metal cap to take hammer blows *
CHISEL: STANLEY 25MM BUTT
SKU:
ST-166160
* Stanley chisels have been preferred by tradespeople for decades * Blades are hot forged hardened tempered then ground to a fine finish * Blades are made from high carbon alloy steel * Handles are tough cellulose acetate butyrate * Contractor grade butt chisels feature a short bevelled blade and handle is fitted with a metal cap to take hammer blows *
SURFORM BLADE: STANLEY FLAT
SKU:
ST-215200
RAFTER SQUARE: 400X600 STANLEY
SKU:
ST-455300
Large steel metric square for carpentry and general construction * Excellent for use on sheet materials such as fibre cement plywood and particle board * Strong metal construction that can resist rust * Graduated every 2mm * Has rafter Graduations embossed into steel for legibility and durability * Rafter table *
RAFTER SQUARE: 400X600MM STANL
SKU:
ST-455400
WONDER BAR: STANLEY 300MM
SKU:
ST-575400
NAIL PUNCH: 3PC SET STANLEY
SKU:
ST-582300
NAIL PUNCH: STANLEY 0.8MM CONTRACTORS
SKU:
ST-589110
NAIL PUNCH: STANLEY 2.4MM CONTRACTORS
SKU:
ST-589130
ROLLER TOOL CHEST: 9 DRAWS W/TOOLS 163PCS
SKU:
TB-100040
* This roller tool chest comes with 5 draws for tools and two larger draws for larger items + 2 deep side draws
* Comes complete with tools inc: Socket sets 1/4 3/8 and 1/2 drives
* Screwdriver set together with a range of driver bits
* Hex yeys torx keys
* Ratchet spanner set double end ring spanners mitre square level tape measure pliers hammers
* Total tools 194pcs
ROLLER TOOL CHEST: 7 DRAWS S/STEEL WOOD TOP
SKU:
TB-100050
TOOL CHEST: 7 DRAWS S/STEEL W/TOP 153PC TOOLS
SKU:
TB-100052
* This roller tool chest is fitted with 7 draws for tools and side cabinet for bulkier items * Mounted on castors for manoverability
* Top is 38.0mm wood
* Manufactured from 430 stainless steel x 0.8mm thickness and 1.0mm for panel & shelf * 90pc Socket set
* 22pc Metric combination Spanner Set
* 30pc Ratchet ring spanner set
* 11pc Pliers, side cutter, 11pc Tin snip set
* All profecional quality tools
TOOL CHEST: 12 DRAWS ROLLER S/STEEL W/TOP
SKU:
TB-100060
TOOL CHEST: 4 DRAWS 64PC TOOLS
SKU:
TB-100084
TOGGLE CLAMP: GH-101-A VERT
SKU:
TC-200000
TOGGLE CLAMP: GH-101-B VERT
SKU:
TC-200020
TOGGLE CLAMP: GH-102-B VERT
SKU:
TC-200040
TOGGLE CLAMP: GH-12130 VERT
SKU:
TC-200058
TOGGLE CLAMP: GH-12265 VERT
SKU:
TC-200059
TOGGLE CLAMP: GH-101-D VERT
SKU:
TC-200060
TOGGLE CLAMP: GH-101-D1 VERT
SKU:
TC-200080
TOGGLE GLAMP: GH-12205 VERT
SKU:
TC-200165
TOGGLE CLAMP: GH-101-J VERT
SKU:
TC-200180
TOGGLE CLAMP: FL-12002B VERT OR GH-11502-B
SKU:
TC-200190
TOGGLE CLAMP: GH-200-W HORZ
SKU:
TC-200200
TOGGLE CLAMP: GH-200-WL HORZ
SKU:
TC-200220
TOGGLE CLAMP: GH-200-WH HORZ
SKU:
TC-200240
TOGGLE CLAMP: GH-220-WH HORZ
SKU:
TC-200260
TOGGLE CLAMP: GH-200-WLH HORZ
SKU:
TC-200280
TOGGLE CLAMP: GH-220-WLH HORZ
SKU:
TC-200300
TOGGLE CLAMP: GH-201-A HORZ
SKU:
TC-200320
TOGGLE CLAMP: GH-201-AL HORZ
SKU:
TC-200360
TOGGLE CLAMP: GH-201-B HORZ
SKU:
TC-200380
TOGGLE CLAMP: GH-201-BSS HORZ STAINLESS STEEL
SKU:
TC-200382
TOGGLE CLAMP: GH-204-G HORZ
SKU:
TC-200460
TOGGLE CLAMP: GH-301-A HORZ PUSH TYPE
SKU:
TC-200540
* The GH-301A clamp is suitable for light duty operations
* Each clamp is supplied with pressed steel base
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* Plunger locks in extended or retracted position
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-301A clamp is supplied with red vinyl hand grip
* Holding capacity is 45kg
* Stroke is 18.0mm with handle locking in horizontal position
* This is a small clamp o/a length is 65.0mm with three hole mounting base
TOGGLE CLAMP: GH-301-B HORZ PUSH TYPE
SKU:
TC-200546
Description:
* The GH-301-B Fast clamp quick release hand tool, 45kg holding capacity push pull
Quick clip is the use of leverage, linkage mechanism, such as the principle of self-locking through steel stamping
Specification
* Model: GH-301-B
* Material: HCS / High Carbon Steel
* Type: Push pull type
* Quantity: 1pc
* Holding Capacity: 45kg
* Handle Opens: 190°
* Plunger Stroke: 16mm
* Spindle Supplied: M4x20
* Quantity: 1pc
* Usage: Toggle Clamp
* DIY Supplies: Metalworking
* Suitable for: Wide machine tools, for production needs to be fixed workpiece machining industries.
TOGGLE CLAMP: GH-302F HORZ PUSH TYPE
SKU:
TC-200580
* The GH-302F clamp is suitable for light medium duty operations
* Each clamp is supplied with a pressed steel base
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-302F clamp is supplied with red vinyl hand grip
* Holding capacity is 136kg
* Stroke is 25.0mm with handle locking in a 45deg position
TOGGLE CLAMP: GH-303-E HORZ PUSH TYPE
SKU:
TC-200600
* * The GH-303E clamp is suitable for light medium or heavy duty operations
* Each clamp is supplied with a pressed steel base
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-303E clamp is supplied with red vinyl hand grip
* Holding capacity is 454kg
* Stroke is 25.0mm with handle locking in a 45deg position
T
TOGGLE CLAMP: GH-304-CM HORZ PUSH TYPE
SKU:
TC-200620
* The GH-304-CM is a horizontal push clamp
* Cast base with 4 mounting holes
* handle sits at 45 degrees when in the locked position
* The plunger has a threaded end and is supplied with end screw for fine adjustment
* This clamp is supplied with red vinyl hand grip
* Holding capacity 227kg
Very solid clamp and is highly recomended for horizontal clamping
TOGGLE CLAMP: GH-305-C HORZ PUSH TYPE
SKU:
TC-200640
The GH-305E is a horizontal push clamp
* Cast base with 4 mounting holes
* handle sits at 90 degrees when in the locked position
* The plunger has a threaded end and is supplied with end screw for fine adjustment
* This clamp is supplied with red vinyl hand grip
* Holding capacity 227kg
Very solid clamp and is highly recomended for horizontal clamping
TOGGLE CLAMP: GH-304-E HORZ PUSH TYPE
SKU:
TC-200660
The GH-304E is a horizontal push clamp
* Cast base with 4 mounting holes
* handle sits at 45 degrees when in the locked position
* The plunger has a threaded end and is supplied with end screw for fine adjustment
* This clamp is supplied with red vinyl hand grip
* Holding capacity 386kg *
Very solid clamp and is highly recomended for horizontal clamping
TOGGLE CLAMP: GH-305-E HORZ PUSH TYPE
SKU:
TC-200680
** The GH-305E clamp is suitable for light medium or heavy duty operations
* Each clamp is supplied with a ductile iron base, precision machined for flatness
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* Plunger locks in extended or retracted position
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-305E clamp is supplied with red vinyl hand grip
* Holding capacity is 386kg
* Stroke is 36.0mm with handle locking in verticle position
TOGGLE CLAMP: GH-304-H HORZ PUSH TYPE
SKU:
TC-200700
* The GH-304H clamp is suitable for light medium or heavy duty operations
* Each clamp is supplied with a ductile iron base, precision machined for flatness
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* Plunger locks in extended or retracted position
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-304H clamp is supplied with red vinyl hand grip
* Holding capacity is 680kg
TOGGLE CLAMP: GH-305-H HORZ PUSH TYPE
SKU:
TC-200720
* The GH-305H clamp is suitable for light medium or heavy duty operations
* Each clamp is supplied with a ductile iron base, precision machined for flatness
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* Plunger locks in extended or retracted position
* These clamps are supplied with adjustable end screw for fine adjustment
* The GH-305H clamp is supplied with red vinyl hand grip
* Holding capacity is 680kg
TOGGLE CLAMP: GH-305HM HORZ PUSH TYPE
SKU:
TC-200722
* The GH-305HM clamp is suitable for light medium or heavy duty operations
* Each clamp is supplied with a ductile iron base, precision machined for flatness
* Close tolerances between the base and plunger allow these clamps to be used for pin locating gauges as well as clamping devices
* Plunger locks in extended or retracted position
* These clamps are supplied with adjustable end screw for fine adjustment
