- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
ROTARY TABLE: HV-3 3" ALTO W/CHUCK
Excl. GST: $495.00
Incl. GST: $569.25
Incl. GST: $569.25
ANGLE PLATE: 16" X 12" X 9" OPEN END
Excl. GST: $585.00
Incl. GST: $672.75
Incl. GST: $672.75
ROUND VICE: 77.0MM JAWS SUIT 4″ ROTARY TABLE
Excl. GST: $59.00
Incl. GST: $67.85
* This round vice designed for mounting on small rotary tables
* Manufactured from close grain cast iron
* This model is suitable for 100mm tables
* Moving jaw has V-Groove to hold round oblects
* Pre-drilled to suit table slots of the rotary tables
| Weight | 1.28 kg |
|---|---|
| Dimensions | 0.16 × 0.18 × 0.05 cm |
In stock
Related products
ROTARY TABLE: HV-4 4″ HOMGE
SKU:
RT-9580005
* Homge rotary tables are made in Taiwan
* This company is renown for their accuracy and overall quality
* This Rotary Table is fitted with a 4" slotted face plate
* This is to fit T-Slot nuts for fixing a workpiece
* Can be used both horizontal and verticle making it a very versitile indexing fixtureTW
ROTARY TABLE: RT-6T 6″ ALTO TILTING
SKU:
RT-9580007A
* these Alto Rotary Tables are made from high density Meehanite casting with ground finish
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* Tilting table model for versitility
ROTARY TABLE: HV-6 6″ HOMGE COMPLETE
SKU:
RT-9580007B
* Homge Rotary Tables are made from high density Meehanite casting with ground finish * Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1 * The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
POWER ROTARY TABLE: 10″ LIBO
SKU:
RT-9580115
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* Controller has three wires, one of them is for powercord conected to DC 24W - 48V. Motor should be conected to 4 pin aviation socket and motor encoder should be connected to the 6 pin aviation conector
DIVIDING PLATES: HV-8,” DP-2
SKU:
RT-9581008
DIVIDING PLATES: FOR TSK-10″
SKU:
RT-9581014
TAILSTOCK: TS-4
SKU:
RT-9581056
TAILSTOCK: TS-2 SUIT 8″ TO 12″ CENTRE HEIGHT (LIBO)
SKU:
RT-9581064