- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
ROTARY TABLE: HV-3 3" ALTO W/CHUCK
Excl. GST: $495.00
Incl. GST: $569.25
Incl. GST: $569.25
ANGLE PLATE: 16" X 12" X 9" OPEN END
Excl. GST: $585.00
Incl. GST: $672.75
Incl. GST: $672.75
ROUND VICE: 77.0MM JAWS SUIT 4″ ROTARY TABLE
Excl. GST: $59.00
Incl. GST: $67.85
* This round vice designed for mounting on small rotary tables
* Manufactured from close grain cast iron
* This model is suitable for 100mm tables
* Moving jaw has V-Groove to hold round oblects
* Pre-drilled to suit table slots of the rotary tables
| Weight | 1.28 kg |
|---|---|
| Dimensions | 0.16 × 0.18 × 0.05 cm |
In stock
Related products
ROTARY TABLE: HV-3 3″ ALTO W/CHUCK
SKU:
RT-9580001A
ROTARY TABLE: HV-4 4″ VERTEX TABLE W/CHUCK
SKU:
RT-9580002B
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* This model comes complete with 3 jaw chuck
ROTARY TABLE: HV-4 4″ ALTO WITH 100MM 3 JAW CHUCK
SKU:
RT-9580003
* This 4" rotary table is a very versitile unit
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with 3 tee slots in table
* This rotary table comes with 100mm 3 jaw chuck in seperate package
* Chuck is on backing plate and can be removed
ROTARY TABLE: HV-6 6″ ALTO
SKU:
RT-9580007
* Homge Rotary Tables are made from high density Meehanite casting with ground finish * Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
ROTARY TABLE: HV-8 8″ ALTO
SKU:
RT-9580009
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
DIVIDING PLATES: HV10-12-14″
SKU:
RT-9581010
DIVIDING PLATES: FOR TSK-10″
SKU:
RT-9581014
TAILSTOCK: TS-1 SUIT 3″ TO 6″ CENTRE HEIGHT (LIBO)
SKU:
RT-9581060