- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
ROTARY TABLE: HV-4 4″ VERTEX TABLE W/CHUCK
$807.66
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1′ min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* This model comes complete with 3 jaw chuck
| Weight | 9.9 kg |
|---|---|
| Dimensions | 0.21 × 0.23 × 0.25 cm |
In stock
Related products
ROTARY TABLE: HV-4 4″ ALTO TILTING
SKU:
RT-9580002A
* This 4" Tilting rotary table is a very versitile unit
* Tilting range is 0 - 90 Degrees with positive locking
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with tee slots in table
* Can be bolted in verticle or horizontal position
ROTARY TABLE: HV-4 4″ HOMGE
SKU:
RT-9580005
* Homge rotary tables are made in Taiwan
* This company is renown for their accuracy and overall quality
* This Rotary Table is fitted with a 4" slotted face plate
* This is to fit T-Slot nuts for fixing a workpiece
* Can be used both horizontal and verticle making it a very versitile indexing fixtureTW
ROTARY TABLE: HV-8 8″ ALTO
SKU:
RT-9580009
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
POWER ROTARY TABLE: 10″ LIBO
SKU:
RT-9580115
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* Controller has three wires, one of them is for powercord conected to DC 24W - 48V. Motor should be conected to 4 pin aviation socket and motor encoder should be connected to the 6 pin aviation conector
ROTARY CROSS TABLE: 330 X 220MM LIBO
SKU:
RT-9580205
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting borin
DIVIDING PLATES: FOR TSK-10″
SKU:
RT-9581014
TAILSTOCK: TS-4
SKU:
RT-9581056
TAILSTOCK: TS-2 SUIT 8″ TO 12″ CENTRE HEIGHT (LIBO)
SKU:
RT-9581064