- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
HYDRAULIC OIL: RENEP CGLP 220T 20 LTR SLIDEWAY LUBE
SKU:
OIL600160
LACTUCA LT3000 1 LTR CUTTING OIL SOLUBLE
SKU:
OIL600420
* Lactuca LT2 is a soluble cutting fluid with a recomended mix ratio of 33:1/20
* Suitable for lathes mills bandsaws threading in most materials
* Classical machining, brass bar turning. Works well on fine carbon steels.
* LACTUCA LT 3000 is very easy to use, simply by pouring it into good quality water.
* Excellent cooling and lubricant power.
* Efficient protection of machined parts and machines against corrosion.
* Good mechanical performances, providing:
* Reduced cutting efforts
* Extended tool lifetime
* Very good surface finish to parts.
* Properties in service:
* Excellent stability over time increases drain intervals;
* Cuttings have low rate of humidity;
* Good anti-foaming properties.
* Resist to the development of bacteria and mould very well,so is more environmentally and operator friendly.
* Very multifunctional
LACTUCA LT3000 5 LIR CUTTING OIL SOLUBLE
SKU:
OIL600425
* Lactuca LT2 is a soluble cutting fluid with a recomended mix ratio of 33:1/20
* Suitable for lathes mills bandsaws threading in most materials
* Classical machining, brass bar turning. Works well on fine carbon steels.
* LACTUCA LT 3000 is very easy to use, simply by pouring it into good quality water.
* Excellent cooling and lubricant power.
* Efficient protection of machined parts and machines against corrosion.
* Good mechanical performances, providing:
* Reduced cutting efforts
* Extended tool lifetime
* Very good surface finish to parts.
* Properties in service:
* Excellent stability over time increases drain intervals;
* Cuttings have low rate of humidity;
* Good anti-foaming properties.
* Resist to the development of bacteria and mould very well,so is more environmentally and operator friendly.
* Very multifunctional
LACTUCA LT3000 20 TLR CUTTING OIL SOLUBLE
SKU:
OIL600430
* Lactuca LT2 is a soluble cutting fluid with a recomended mix ratio of 33:1/20
* Suitable for lathes mills bandsaws threading in most materials
* Classical machining, brass bar turning. Works well on fine carbon steels.
* LACTUCA LT 3000 is very easy to use, simply by pouring it into good quality water.
* Excellent cooling and lubricant power.
* Efficient protection of machined parts and machines against corrosion.
* Good mechanical performances, providing:
* Reduced cutting efforts
* Extended tool lifetime
* Very good surface finish to parts.
* Properties in service:
* Excellent stability over time increases drain intervals;
* Cuttings have low rate of humidity;
* Good anti-foaming properties.
* Resist to the development of bacteria and mould very well,so is more environmentally and operator friendly.
* Very multifunctional
MARTOL EP 180: 1 LTR NEAT CUTTING,TAPPING, DRILLING OIL
SKU:
OIL600456
SPIRIT WBF 7200: 1 LTR CUTTING OIL FOR STAINLESS
SKU:
OIL600460
SPIRIT WBF 7200: 5 LTR CUTTING OIL FOR STAINLESS
SKU:
OIL600462
TRIM E709: 1 LTR SOLUBLE CUTTING OIL
SKU:
OIL600466
* TRIM® E709 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems
* It has broad application in machining and grinding on a wide range of materials
* The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs
* The stable and predictable performance of TRIM® E709 makes it a first choice for high-quality, consistent parts manufacturing
Recomended Metalworking Concentrations
* Light duty machining and grinding 5%
* Medium Duty 7%
* Heavy Duty 10%
TRIM E709: 5 LTR SOLUBLE CUTTING OIL
SKU:
OIL600468
* TRIM® E709 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems
* It has broad application in machining and grinding on a wide range of materials
* The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs
* The stable and predictable performance of TRIM® E709 makes it a first choice for high-quality, consistent parts manufacturing
Recomended Metalworking Concentrations
* Light duty machining and grinding 5%
* Medium Duty 7%
* Heavy Duty 10%
TRIM E709: 20 LTR SOLUBLE CUTTING OIL
SKU:
OIL600470
* TRIM® E709 is high quality universal soluble oil which requires minimal maintenance in even the most demanding fluid management systems
* It has broad application in machining and grinding on a wide range of materials
* The high levels of both chemical and mechanical lubricity in this product handle the tough machining and grinding jobs
* The stable and predictable performance of TRIM® E709 makes it a first choice for high-quality, consistent parts manufacturing
Recomended Metalworking Concentrations
* Light duty machining and grinding 5%
* Medium Duty 7%
* Heavy Duty 10%
TRANSMISSION OIL: 5LTR FUCHS TITAN ATF D3
SKU:
OIL700280
TITAN ATF D3
A multifunctional ATF for Passenger Cars and Commercial Vehicles requiring a Dexron® III specification
TITAN ATF D3 is a Multifunctional Automatic Transmission Fluid, providing longer life and smoother gear shifts. Recommended for Passenger Cars and Commercial Vehicles requiring a Dexron® III specification. Automatic Transmission Fluid is specially formulated to conform to GM and Ford specifications. Supercedes Dexron®.
Not suitable where Dexron VI is called for.
Suitable for use for the following applications: ATF Dexron® III Ford MERCON® Allison C-4 Caterpillar TO-2.
TRANSMISSION OIL: 20LTR FUCHS TITAN ATF D3
SKU:
OIL700282
TITAN ATF D3
A multifunctional ATF for Passenger Cars and Commercial Vehicles requiring a Dexron® III specification
TITAN ATF D3 is a Multifunctional Automatic Transmission Fluid, providing longer life and smoother gear shifts. Recommended for Passenger Cars and Commercial Vehicles requiring a Dexron® III specification. Automatic Transmission Fluid is specially formulated to conform to GM and Ford specifications. Supercedes Dexron®.
Not suitable where Dexron VI is called for.
Suitable for use for the following applications: ATF Dexron® III Ford MERCON® Allison C-4 Caterpillar TO-2.
DIESEL ENGINE OIL: RUBIA CF2-40 20LTR (2 STROKE)
SKU:
OIL700310
Monograde lubricant for two stroke Diesel engines SPECIFICATIONS International specifications API CF-2/CF MIL.L. 46152B Meets the requirements of  Detroit Diesel : Oil typ 1 and 2 for series : 53, 71, 92, 110 and 149 marine APPLICATIONS This lubricant is suitable for all two stroke Diesel engines when API CF-2 or API CD II specifications are required. TOTAL RUBIA CF-2 40 has been especially developed for the lubrication of two stroke Detroit Diesel engines. It also can be used in Diesel or gasoline engines of old vehicles. PERFORMANCES AND CUSTOMER BENEFITS  Good anti-wear and anti-corrosion properties  Excellent anti-oxidation properties allowing long time idle or very severe working conditions (hot climates, heavy load…)  Low ash value ensuring good engine cleanliness  Very high performance detergent and dispersant additives PHYSICAL AND CHEMICAL CHARACTERISTICS* TOTAL RUBIA CF-2 40 Method Value Kinematic Viscosity at 40°C mm2 /s ASTM D445 145.9 Kinematic Viscosity at 100°C mm2 /s ASTM D445 14.5 Viscosity Index - ASTM D2270 98 T.B.N mgKOH/g ASTM D2896 7.1 Pour Point °C ASTM D97 -15 Sulphated Ash % m/m ASTM D874 0.77
HYDRAULIC OIL: DROSERA MS 68 5 LITRE
SKU:
OIL700340
* Drosera MS 68 is a general all purpose hydraulic oil with properties to suit most application such as: lathe headstock gear oil, Slideway oils for lathes and milling machines - also suitable as hydraukic oil for press brakes and guillotines * Special additives to satisfy wear factors and vicosity *
HYDRAULIC OIL: DROSERA MS 68 20 LITRE
SKU:
OIL700342
* Drosera MS 68 is a general all purpose hydraulic oil with properties to suit most application such as: lathe headstock gear oil, Slideway oils for lathes and milling machines - also suitable as hydraukic oil for press brakes and guillotines * Special additives to satisfy wear factors and vicosity *
HYDRAULIC OIL: DROSERA MS 68 208 LITRE
SKU:
OIL700344
* Drosera MS 68 is a general all purpose hydraulic oil with properties to suit most application such as: lathe headstock gear oil, Slideway oils for lathes and milling machines - also suitable as hydraukic oil for press brakes and guillotines * Special additives to satisfy wear factors and vicosity *
MAGNAGLIDE OIL: CASTROL D68 20 LITRE / SLIDEWAY
SKU:
OIL700500
escription
Castrol Magnaâ„¢ SW D (previously called Magnaglide D Range) is specially formulated for the lubrication of slideways
on machine tools. These oils are fortified with selected oiliness, extreme pressure additives and a special material to
impart tackiness and adhesiveness.
Magna SW D lubricants are noted for their usual ability to overcome the stick-slip motion ordinarily associated with slow
moving tool parts. They reduce machine tool carriage chatter and possess the necessary adhesive characteristics to
prevent squeezing out of the lubricant.
Application
Magna SW D can be used on all horizontal and vertical slideways where a high quality demulsifying lubricant is
required for slideway protection and to maximize coolant life; the outstanding frictional characteristics of the
products prevents stick-slip, improving surface finish and tolerances of machined components and reducing
rejection rates.
Magna SW D meets the exacting demands in the following applications; planers, grinders, horizontal boring
machines, shapers, jig borers, and milling machines.
Magna SW D 32 can be used as a combined hydraulic and slideway oil.
The Magna SW D range meets the requirements of:
Cincinnati Lamb (Milacron) P-47, P-50 and P-53 (depending on viscosity grade)
DIN 51502 – CGLP
DIN 51524 Part II (July 2004) – including ISO 13357-1/-2 filtration test
Suitable for Müller Weingarten equipment as hydraulic oil
HYSPIN OIL: AWS-10 20LTR DRUM / SOLD PER LITRE
SKU:
OIL700504
* Description
* The Castrol Hyspin AWSTM hydraulic oil range of premium lubricants are based upon severely
* Hydro treated premium mineral base stocks (group II based oil) enhanced with a stabilised zinc
additive system.
* Applications
* Hyspin AWS has been specially formulated to provide outstanding anti-wear and thermal
* Stability performance using proven additive technoloDisgy.
* The careful blend of additives with a high quality base stock ensures that Hyspin AWS has excellent hydrolytic and oxidative stability
while exhibiting a minimal tendency to produce sludge and deposits
* In addition, Hyspin AWS
provides corrosion protection to ferrous and yellow metal components found within a hydraulic
system.
* This range is designed for use in industrial hydraulic systems which require anti-wear
protection
* It is also suitable for other duties in which lubricants of high oxidation stability and
lubrication performance are required, such as lightly loaded gears, some variable speed units and bearings.
* The Hyspin AWS range is compatible with the most commonly used nitrile, silicone and fluropolymer seal materials.
Hyspin AWS is classified as follows:
* DIN 51502 classification – HLP and ISO 6743/4 – Hydraulic Oil Type HM Hyspin AWS grades meet the requirements (for appropriate viscosity grade) of:
* DIN 51524 Part 2
HYDRAULIC OIL: RENOLIN B HVI 46 5 LITRE FUCHS
SKU:
OIL700508
HYDRAULIC OIL: RENOLIN B HVI 46 20 LITRE FUCHS
SKU:
OIL700510
HYDRAULIC OIL: RENOLIN B HIV PLUS 46 205LTR FUCHS
SKU:
OIL700525
ECOCOOL: 610 20LTR (SURFACE GRIDING ) FUCHS
SKU:
OIL700535
ECOCOOL: 700 NBF 20LTR (SURFACE GRINDING) FUCHS
SKU:
OIL700540
RUSTILO: DWX 22 20 LITRE (NOW ILS NAME CHANGE) ILS DRP 22
SKU:
OIL700552
Description
Castrol Rustiloâ„¢ DWX 22 is a powerful solvent deposited corrosion preventive with dewatering properties.
The product, after evaporation of the solvent, leaves a soft greasy protective film.
Application
Rustilo DWX 22 gives medium term corrosion protection. It is ideal for protection of machine tools and components
prior to storage or transportation.
The product also shows water displacing properties.
Although Rustilo DWX 22 can be applied by brushing or spraying, its dewatering action is most effective if the articles to
be protected can be immersed in a dip tank.
Advantages
Contains powerful corrosion inhibitor package suitable for moderate conditions which provides reliable
protection of components.
Good water displacement and penetrating properties which avoids water entrapment and corrosion under film.
Good stability against acidic and alkaline contraminations which enables a long bath-lifetime to help reduce
operational cost.
Good mechanical film strength and finger print suppressing properties - highly finished work is not damaged by
handling which improves component quality.
If required, protective films of Rustilo DWX 22 can be removed by using a petroleum solvent or alkaline process
cleaner, all available from Castrol.
GREASE: PREMIUM 20 LITRE H/DUTY
SKU:
OIL700570
GREASE: PREMIUM H/DUTY 450G CARTRIDGE MULTI PURPOSE
SKU:
OIL700574
GREASE: H/DUTY CASTROL SPHEEROL EP 450G CARTRIDGE
SKU:
OIL700578
GREASE: H/DUTY CASTROL 2.5KG TUB MULTI PURPOSE
SKU:
OIL700582
GREASE: MX-G4-500 500G LANOLIN GREASE
SKU:
OIL700590
* LANOX-MX4 Lanolin Grease is great for:
* Waterproofing; Protecting Leather; Preserving Timber from Water, Cracking, and Rot; Anti-Sieze for Bolts, Nuts, and Threaded Rod; and stops Electrolysis with Dissimilar Metals in contact with eachother
* Highly suitable for: Anti-Corrosion; Rust Proofing, and Anti-Fouling of all metals used in automotive, commercial, farming, industrial, marine, mining, and transport applications
* Non-toxic
* NSF Food Grade
* Non-Conductive
* Environmentally & User Friendly
ADBLUE: 4LTR DIESEL EMMISION CONTROL
SKU:
OIL700600
CUTTING OIL: RELTON FOR ALUMINUM 1 GALLON
SKU:
OIL700700
