- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
JOBBER DRILL: 29/64″ HSS-M2 ETS
SKU:
DBT2083029
* Jobber-length drills are the most common type of drill
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length
* A 1⁄8 in (3.2 mm) diameter drill can drill a hole 1 5⁄8 in (41.3 mm) deep since it is thirteen times the diameter in flute length
* These jobber drill bits are manufactured from quality HSS-M2 for durability and long service life
* Aircraft length drill *
JOBBER DRILL: 15/32″ HSS-M2 ETS
SKU:
DBT2083030
* Jobber-length drills are the most common type of drill
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length
* A 1⁄8 in (3.2 mm) diameter drill can drill a hole 1 5⁄8 in (41.3 mm) deep since it is thirteen times the diameter in flute length
* These jobber drill bits are manufactured from quality HSS-M2 for durability and long service life
* Aircraft length drill *
JOBBER DRILL: 31/64″ HSS-M2 ETS
SKU:
DBT2083031
* Jobber-length drills are the most common type of drill
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length
* A 1⁄8 in (3.2 mm) diameter drill can drill a hole 1 5⁄8 in (41.3 mm) deep since it is thirteen times the diameter in flute length
* These jobber drill bits are manufactured from quality HSS-M2 for durability and long service life
* Aircraft length drill *
JOBBER DRILL: 17/32″ HSS-M2 ETS
SKU:
DBT2083031A
* Jobber-length drills are the most common type of drill
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length
* A 1⁄8 in (3.2 mm) diameter drill can drill a hole 1 5⁄8 in (41.3 mm) deep since it is thirteen times the diameter in flute length
* These jobber drill bits are manufactured from quality HSS-M2 for durability and long service life
* Aircraft length drill *
JOBBER DRILL: 1/2″ HSS-M2 ETS
SKU:
DBT2083032
* Jobber-length drills are the most common type of drill
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* So a 1⁄2 in (12.7 mm) diameter drill will be able to drill a hole 4 1⁄2 in (114.3 mm) deep since it is nine times the diameter in length
* A 1⁄8 in (3.2 mm) diameter drill can drill a hole 1 5⁄8 in (41.3 mm) deep since it is thirteen times the diameter in flute length
* These jobber drill bits are manufactured from quality HSS-M2 for durability and long service life
* Aircraft length drill *
JOBBER DRILL: 1.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091016
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 1.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091018
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 2.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091020
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 2.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091025
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 3.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091030
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 3.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091035
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 4.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091040
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 4.2MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091042
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 4.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091045
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 5.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091050
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 5.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091055
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 6.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091060
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 6.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091065
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 6.8MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091068
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 7.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091070
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 7.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091075
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 8.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091080
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 8.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091085
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 9.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091090
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBERDRILL: 9.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091095
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 10.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091110
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort
JOBBER DRILL: 10.2MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091120
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort
JOBBER DRILL: 10.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091150
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 11.0MM HSS=Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091211
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 11.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091215
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 12.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091218
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 12.5MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091220
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 13.0MM HSS-Co5 TiAIN RED BAND (SOMTA)
SKU:
DBT2091224
* These Red Band Somta Jobber drills come with TIAIN finished for durability and long service life
* The length of the flutes is between nine and fourteen times the diameter of the drill, depending on the drill size
* The Red Band drills are suitable for drilling tough treatable steels and offer clean cutting with minimal effort *
JOBBER DRILL: 3.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092090
JOBBER DRILL: 4.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092120
JOBBER DRILL: 5.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092150
JOBBER DRILL: 6.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092180
JOBBER DRILL: 6.5MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092195
JOBBER DRILL: 7.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092210
JOBBER DRILL: 8.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092240
JOBBER DRILL: 10.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092280
JOBBER DRILL: 11.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092285
JOBBER DRILL: 12.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092290
JOBBER DRILL: 13.0MM HSS-Co5 UDL LONG CHIP (SOMTA)
SKU:
DBT2092295
PANEL DRILL: 4.85MM D/END #11
SKU:
DBT2180011
PANEL DRILL: 3.30MM D/END #30
SKU:
DBT2180030
PANEL DRILL: 4.80MM S/END #11
SKU:
DBT2180058
SPOT WELD DRILL: HSS-Co5 6.0 X 66MM 90 DEG
SKU:
DBT2192006
SPOT WELD DRILL: HSS-Co5 8.0 X 79MM 90 DEG
SKU:
DBT2192008
SPOT WELD DRILL: HSS-Co5 8.0 X 44MM 90 DEG
SKU:
DBT2192010
SPOT WELD DRILL: HSS-Co5 10.0 X 89MM 90 DEG
SKU:
DBT2192011
SPOT WELD DRILL: HSS-Co5 12.0 X 102MM 90 DEG
SKU:
DBT2192012
ARMOUR PIERCING DRILL: Co8E MT2 11.0MM (SOMTA)
SKU:
DBT2632806
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT2 12.0MM (SOMTA)
SKU:
DBT2632808
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT2 13.0MM (SOMTA)
SKU:
DBT2632810
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT2 14.0MM (SOMTA)
SKU:
DBT2632812
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT2 16.0MM (SOMTA)
SKU:
DBT2632820
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT2 18.0MM (SOMTA)
SKU:
DBT2632824
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 19.0MM (SOMTA)
SKU:
DBT2632826
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 20.0MM (SOMTA)
SKU:
DBT2632828
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 21.0MM (SOMTA)
SKU:
DBT2632829
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 22.0MM (SOMTA)
SKU:
DBT2632830
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 24.0MM (SOMTA)
SKU:
DBT2632836
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT3 25.0MM (SOMTA)
SKU:
DBT2632838
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 26.0MM (SOMTA)
SKU:
DBT2632842
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
AMROUR PIERCING DRILL: Co8E MT4 28.0MM (SOMTA)
SKU:
DBT2632844
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 30.0MM (SOMTA)
SKU:
DBT2632848
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 32.0MM (SOMTA)
SKU:
DBT2632852
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 35.0MM (SOMTA)
SKU:
DBT2632856
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 36.0MM (SOMTA)
SKU:
DBT2632858
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 40.0MM (SOMTA)
SKU:
DBT2632860
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT4 45.0MM (SOMTA)
SKU:
DBT2632862
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
ARMOUR PIERCING DRILL: Co8E MT5 50.0MM (SOMTA)
SKU:
DBT2632864
* Maunufactured by Somta SA
* Armour piercing drills were designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 130deg notched point
* Available in morse taper shank from MT2 to MT5 from 11.0 to 50.0mm
RAIL DRILL: Co8E MT2 22.0MM (SOMTA)
SKU:
DBT2632880
* These special drills are manufactured by Somta SA
* Rail drills are designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 135deg notched point
* These drills come with MT2, 3, 4 tapers with a range from 22.0 - 35.0mm
* Short flute length and specialy designed for driilng railway lines
RAIL DRILL: Co8E MT3 26.0MM (SOMTA)
SKU:
DBT2632882
* These special drills are manufactured by Somta SA
* Rail drills are designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 135deg notched point
* These drills come with MT2, 3, 4 tapers with a range from 22.0 - 35.0mm
* Short flute length and specialy designed for driilng railway lines
RAIL DRILL: Co8E MT3 28.0MM (SOMTA)
SKU:
DBT2632884
* These special drills are manufactured by Somta SA
* Rail drills are designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 135deg notched point
* These drills come with MT2, 3, 4 tapers with a range from 22.0 - 35.0mm
* Short flute length and specialy designed for driilng railway lines
RAIL DRILL: Co8E MT3 32.0MM (SOMTA)
SKU:
DBT2632886
* These special drills are manufactured by Somta SA
* Rail drills are designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 135deg notched point
* These drills come with MT2, 3, 4 tapers with a range from 22.0 - 35.0mm
* Short flute length and specialy designed for driilng railway lines
RAIL DRILL: Co8E MT3 35.0MM (SOMTA)
SKU:
DBT2632888
* These special drills are manufactured by Somta SA
* Rail drills are designed for drilling work-hardened and heat treated steels
* They are capable of drilling materials like Hardox and is the recommended drilling equipment by the manufacturers ( SSAB of Sweden ) of this range of tough material
* Manufactured to works standard with 15deg helix and 135deg notched point
* These drills come with MT2, 3, 4 tapers with a range from 22.0 - 35.0mm
* Short flute length and specialy designed for driilng railway lines