- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
END MILL: 12.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210212
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 13.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210213
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 14.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210214
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 16.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210216
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 18.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210218
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 20.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210220
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 22.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210222
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 25.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210225
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 28.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210228
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 30.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210230
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 32.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210232
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 2.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441002
END MILL: 3.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441003
END MILL: 4.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441004
END MILL: 5.0MM FAST CARBIDE CUTTER ALU (SOMTA)
SKU:
EM-7441005
END MILL: 6.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441006
END MILL: 8.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441008
END MILL: 10.0MM FAST CARBIDE 3 FLUTE ALU(SOMTA)
SKU:
EM-7441010
END MILL: 12.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441012
END MILL: 16.0MM FAST CARBIDE 3 FLUTE ALU (SOMTA)
SKU:
EM-7441016
END MILL: 5/32″ CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7443202
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 11/32” CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7443208
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 3/8″ CARBIDE 4 FLUTE STD (INDEX)
SKU:
EM-7443209C
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 1/2″ CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7443211
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 7/8″ CARBIDE 4 FLUTE STD USA
SKU:
EM-7443219
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 1″ CARBIDE 4 FLUTE STD (USA)
SKU:
EM-7443221
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 3/16″ CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7443296
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 5/16″ CARBIDE 4 FLUTE LONG SERIES (INDEX)
SKU:
EM-7443303C
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 3/8″ CARBIDE 4 FLUTE LONG SERIES (INDEX)
SKU:
EM-7443305C
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 1/2″ CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7443307
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 3/4″ CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7443313
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 1.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444900
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 1.5MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444901
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 2.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444902A
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 3.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444903
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 4.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444904
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 5.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444905A
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 6.0MM CARBIDE 4 FLUTE STANDARD (SEA)
SKU:
EM-7444906
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 6.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444906A
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 8.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444908A
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 9.0MM CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7444909
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
NOT IN USE
SKU:
EM-7444910
* These 4 flute end mills are made in USA and offer durability and long tool life * Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut * Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 10.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444910A
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 14.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444914
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 14.0MM CARBIDE 4 FLUTE STANDARD (PALBIT)
SKU:
EM-7444914P
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 16.0MM CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7444916
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 16.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444916A
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 16.0MM CARBIDE 4 FLUTE STANDARD (PALBIT)
SKU:
EM-7444916P
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 18.0MM CARBIDE 4 FLUTE STANDARD (SOMTA)
SKU:
EM-7444918
* These 4 flute end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
END MILL: 22.0MM CARBIDE 4 FLUTE STANDARD (USA)
SKU:
EM-7444922
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are standard length General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 5PC SET VARICUT CARBIDE 4FLUTE COATED (SOMTA)
SKU:
EM-7448000
* These 4 flute Varicut end mills are made by Somta SA
* Offering durability and long tool life
* Manufactured from Solid Carbide in standard length
* General Purpose, 4 Flutes, Single End, Square End Style
* Center Cutting Type, Right Hand Cut
* Fully ground with Bright Finish, Rhc 30 Deg, Rhh 30 Deg,
* Suitable for Plunge Cutting
* Also Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds
e* Varicut is a patened product and is suitable for: Carbon,alloy steels, stainless steel.
fast and high deep of cuts.
END MILL: 3.0MM CARBIDE VARICUT TIAIN COATED 4FLUTE COATED (SOMTA)
SKU:
EM-7448005
END MILL: 4.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448006
END MILL: 5.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448007
END MILL: 6.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448008
END MILL: 8.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448009
END MILL: 10.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448010
END MILL: 12.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448012
END MILL: 16.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448016
END MILL: 20.0MM CARBIDE VARICUT TIAIN COATED 4 FLUTE (SOMTA)
SKU:
EM-7448020
END MILL: 2.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464502
* These 4 flute end mills are made in USA and offer durability and long tool life
* Manufactured from Solid Carbide are long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds * Long Series *
END MILL: 3.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464503
END MILL: 4.0MM CARBIDE 4 FLUTE LONG SERIES (SOMTA)
SKU:
EM-7464504A
END MILL: 5.0MM CARBIDE 4 FLUTE LONG SERIES (SOMTA)
SKU:
EM-7464505A
END MILL: 6.0MM CARBIDE 4 FLUTE LONG SERIES (SOMTA)
SKU:
EM-7464506A
END MILL: 6.0MM CARBIDE 4 FLUTE LONG SERIES (IINDEX)
SKU:
EM-7464506C
END MILL: 8.0MM CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7464508
END MILL: 9.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464509
END MILL: 10.0MM CARBIDE 4 FLUTE LONG SERIES HRC55 (SEA)
SKU:
EM-7464510A
END MILL: 11.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464511
END MILL: 12.0MM CARBIDE 4 FLUTE LONG SERIES HRC55 (SEA)
SKU:
EM-7464512
END MILL: 14.0MM CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7464514
END MILL: 14.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464514A
END MILL: 16.0MM CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7464516
END MILL: 16.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464516A
END MILL: 18.0MM CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7464518
END MILL: 18.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464518A
END MILL: 20.0MM CARBIDE 4 FLUTE LONG SERIES (USA)
SKU:
EM-7464520
END MILL: 20.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464520A
END MILL: 22.0MM CARBIDE 4 FLUTE LONG SERIES (SEA)
SKU:
EM-7464522