- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
WOODRUFF CUTTER: 1009 D1-1/8″ X W5/16″ TRE/SHANK (SOMTA)
SKU:
EM-7210154
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 810 D1-1/4″ X W1/4″ TRE/SHANK (SOMTA)
SKU:
EM-7210160
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1010 D1-1/4″ X W5/16″ TRE/SHANK (SOMTA)
SKU:
EM-7210162
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1210 D1-1/4″ X W3/8″ TRE/SHANK (SOMTA)
SKU:
EM-7210164
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 811 D1-3/8″ X W1/4″ TRE/SHANK (SOMTA)
SKU:
EM-7210170
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1011 D1-3/8″ X W5/16″ TRE/SHANK (SOMTA)
SKU:
EM-7210172
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1211 D1-3/8″ X W3/8″ TRE/SHANK (SOMTA)
SKU:
EM-7210174
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 812 D1-1/2″ X W1/4″ TRE/SHANK (SOMTA)
SKU:
EM-7210180
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1012 D1-1/2″ X W5/16″ TRE/SHANK (SOMTA)
SKU:
EM-7210182
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
WOODRUFF CUTTER: 1212 D1-1/2″ X W3/8″ TRE/SHANK (SOMTA)
SKU:
EM-7210184
*This woodruff cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* These tools are also known as Keyway cutters, T-Slot cutters and Woodruff cutters and all have the same fuction
* Woodruff Keyseat cutters are designed for cutting keyways and keyseats as well as performing general purpose milling operations
* Straight tooth cutters produce a better surface finish than staggered tooth
* M-35 Cobalt works great in most types of materials and will give much better tool life than M2 tooling
INVERTED DOVETAIL CUTTER: 32MM X 16 45DEG (SOMTA)
SKU:
EM-7221008
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 32MM X 16 60DEG (SOMTA)
SKU:
EM-7221008A
* This is an nverted dovetail cutter
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 25MM X 12 45DEG (SOMTA)
SKU:
EM-7221010
* This is an Inverted dovetail cutter
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 25MM X 12 60DEG (SOMTA)
SKU:
EM-7221010A
* This is an Inverted dovetail cutter
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 20MM X 12 45DEG (SOMTA)
SKU:
EM-7221012
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 20MM X 12 60DEG (SOMTA)
SKU:
EM-7221012A
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 20MM X 12 45DEG (SOMTA)
SKU:
EM-7221012C
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 25MM X 12 45DEG (SOMTA)
SKU:
EM-7221014
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 25MM X 12 60DEG (SOMTA)
SKU:
EM-7221014A
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 32MM X 16 45DEG (SOMTA)
SKU:
EM-7221016
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 32MM X 16 60DEG (SOMTA)
SKU:
EM-7221016A
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 40MM X 16 45DEG (SOMTA)
SKU:
EM-7221018
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 40MM X 16 60DEG (SOMTA)
SKU:
EM-7221018A
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 16MM X 12 60DEG (SOMTA)
SKU:
EM-7221040
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
DOVETAIL CUTTER: 16MM X 12 45DEG (SOMTA)
SKU:
EM-7221040A
*This dovetail cutter is manufactured from HSS-M35 (Co5 5% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 16MM X 12 60DEG (SOMTA)
SKU:
EM-7221056
* This is an Inverted dovetail cutter
* 60 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 16MM X 12 45DEG (SOMTA)
SKU:
EM-7221056A
* This is an Inverted dovetail cutter
* 45 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 20MM X 12 45DEG (SOMTA)
SKU:
EM-7221070
* This is an Inverted dovetail cutter
* 45 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 20MM X 12 60DEG (SOMTA)
SKU:
EM-7221070A
* This is an Inverted dovetail cutter
* 60 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 40MM X 16 45DEG (SOMTA)
SKU:
EM-7221072
* This is an Inverted dovetail cutter
* 45 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
INVERTED DOVETAIL CUTTER: 40MM X 16 60DEG (SOMTA)
SKU:
EM-7221072A
* This is an Inverted dovetail cutter
* 60 degree cutter To produce opposite section of dovetail slide to dovetail cutter
* This dovetail cutter is manufactured from HSS-M42 (Co8 8% Cobalt) for durability and long service life
* Dovetail cutters are designed for cutting dovetails in a wide variety of materials
* Dovetail cutters can also be used for chamfering or milling angles on the bottom surface of a part
* Dovetail cutters are available in a wide variety of diameters and in 45 degree or 60 degree angles
* Cutting diameter is measured at the end of the tool, the largest diameter
TEE SLOT CUTTER: 14.0MM X 6.0MM 12.0MM SHANK (SOMTA)
SKU:
EM-7221111
TEE SLOT CUTTER: 16.0MM X 8.0MM 10.0MM SHANK (SOMTA)
SKU:
EM-7221112
TEE SLOT CUTTER: 18.0MM X 8.0MM 12.0MM SHANK (SOMTA)
SKU:
EM-7221120
TEE SLOT CUTTER: 21.0MM X 9.0MM 12.0MM SHANK (SOMTA)
SKU:
EM-7221122
BALL NOSE: HSS 4MM STD (INDEX)
SKU:
EM-7300100
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 5MM STD (INDEX)
SKU:
EM-7300110
** Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 3/16″ STD (INDEX)
SKU:
EM-7301004
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 1/4″ STD (INDEX)
SKU:
EM-7301006
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 5/16″ STD (INDEX)
SKU:
EM-7301008
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 7/8″ STD (INDEX)
SKU:
EM-7301024
** Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 3MM 2FL STANDARD (SOMTA)
SKU:
EM-7302103
BALL NOSE: HSS 4MM 2FL STANDARD (SOMTA)
SKU:
EM-7302104
BALL NOSE: HSS 5MM 2FL STANDARD (SOMTA)
SKU:
EM-7302105
BALL NOSE: HSS 6MM 2FL STANDARD (SOMTA)
SKU:
EM-7302106
BALL NOSE: HSS 8MM 2FL STANDARD (SOMTA)
SKU:
EM-7302108
BALL NOSE: HSS 10MM 2FL STANDARD (SOMTA)
SKU:
EM-7302110
BALL NOSE: HSS 10MM 2FL STANDARD (INDEX)
SKU:
EM-7302110C
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: HSS 12MM 2FL STANDARD (SOMTA)
SKU:
EM-7302112
BALL NOSE: HSS 14MM 2FL STANDARD (SOMTA)
SKU:
EM-7302114
BALL NOSE: HSS 16MM 2FL STANDARD (SOMTA)
SKU:
EM-7302116
BALL NOSE: HSS 20MM 2FL STANDARD (SOMTA)
SKU:
EM-7302120
BALL NOSE: HSS 22MM 2FL STANDARD (SOMTA)
SKU:
EM-7302122
BALL NOSE: 2.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302402
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 3.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302403
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 4.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302404
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 5.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302405
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 6.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302406
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 6.0MM HRC65 CARBIDE COATED 2FL LONG (SEA)
SKU:
EM-7302407
* Quality milling machine cutting tool
* This is a 2 flute ball nose end mill which is manufactured from quality High Speed Steel for durability and long service life
* Extremely high performance. and Ideal for cutting a radius
* Ball nose end mill is a type of milling cutter used in machining operations to create contoured surfaces, curved profiles, and 3D shapes on a workpiece
* It gets its name from the spherical (ball-like) shape of the cutting end. Ball nose end mills are specifically designed for applications where intricate and curved features need to be milled.
* Ball nose end mill specifications include Ball Radius, Diameter, Shank Diameter, Overall Length, Flute Count, Helix Angle, Coating, and Material to define its form, size, features, and suitability for materials like steel, aluminum, or graphite
* These factors determine tool performance in 3D contouring, profiling, and finishing
BALL NOSE: 8.0MM HRC75 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302408
BALL NOSE: 10.0MM HRC65CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302410
BALL NOSE: 12.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302412
BALL NOSE: 12.0MM HRC65 CARBIDE COATED 2FL LONG (SEA)
SKU:
EM-7302413
BALL NOSE: 14.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302414
BALL NOSE: 16.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302416
BALL NOSE: 18.0MM HRC65 CARBIDE COATED 2FL STD (SEA)
SKU:
EM-7302417
BALL NOSE: 20.0MM HRC65 CARBIDE COATED 2 FL STD (SEA)
SKU:
EM-7302418
BALL NOSE: HSS-Co8 3.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303103
BALL NOSE: HSS-Co8 4.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303104
BALL NOSE: HSS-Co8 5.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303105
BALL NOSE: HSS-Co8 6.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303106
BALL NOSE: HSS-Co8 8.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303108
BALL NOSE: HSS-Co8 10.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303110
BALL NOSE: HSS-Co8 12.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303112
BALL NOSE: HSS-Co8 14.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303114
BALL NOSE: HSS-Co8 16.0MM 2 FLUTE STD T/SHANK (SOMTA)
SKU:
EM-7303116
BALL NOSE: HSS-Co8 18.0MM 2 FLUTE STANDARD T/SHANK (SOMTA)
SKU:
EM-7303118
BALL NOSE: HSS-Co8 20.0MM 2 FLUTE STANDARD T/SHANK (SOMTA)
SKU:
EM-7303120
BALL NOSE: HSS-Co8 5/32″ 2 FLUTE STANDARD T/SHANK (SOMTA)
SKU:
EM-7303310
BALL NOSE: HSSTC 3/8″ (INDEX)
SKU:
EM-7304500