- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
TILTING ROTARY TABLE: TSK-150 6″
$1,225.00
* Compact unit with wide range of uses * Tilting range 0-90ø from horizontal to verticle position * Worm is hardened and ground * Ratio is 90:1 * The work table is graduated a full 360ø so that one turn of the handle moves through 4ø *
| Weight | 40 kg |
|---|---|
| Dimensions | 0.2 × 0.2 × 0.16 cm |
In stock
Related products
ROTARY TABLE: HV-4 4″ ALTO TILTING
SKU:
RT-9580002A
* This 4" Tilting rotary table is a very versitile unit
* Tilting range is 0 - 90 Degrees with positive locking
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with tee slots in table
* Can be bolted in verticle or horizontal position
ROTARY TABLE: HV-4 4″ VERTEX TABLE W/CHUCK
SKU:
RT-9580002B
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* This model comes complete with 3 jaw chuck
ROTARY TABLE: HV-6 6″ ALTO
SKU:
RT-9580007
* Homge Rotary Tables are made from high density Meehanite casting with ground finish * Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
ROTARY TABLE: HV 16 16″ VERTEX
SKU:
RT-9580016
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
DIVIDING PLATES: DP1 HV-4/6″ ALTO
SKU:
RT-9581007
DIVIDING PLATES: HV-8,” DP-2
SKU:
RT-9581008
DIVIDING PLATES: HV10-12-14″
SKU:
RT-9581010
TAILSTOCK: TS-4
SKU:
RT-9581056