- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
GEAR SETS: TO SUIT ROL132000
Excl. GST: $50.00
Incl. GST: $57.50
Incl. GST: $57.50
CENTRE: MT3 OLD TAPER
Excl. GST: $20.96
Incl. GST: $24.10
Incl. GST: $24.10
SLIP ROLLS: 1300MM X 1.5MM FLANGED MOTOR 1HP !PH (only)
Excl. GST: $580.00
Incl. GST: $667.00
* This spare single phase flange type motor is to suit the 1300mm x 1.5 slip rolls
| Weight | 0.7 kg |
|---|---|
| Dimensions | 0.36 × 0.25 × 0.25 cm |
In stock
Related products
AKYAPAK: HYDRAULIC ROLLS 3100 X 40.0MM
SKU:
ROL131260
* 4 Roller Plate bending machine
* Precise pinching of plate between top and bottom rolls.
* Legth of flat ends minimised.
* Cone rolling device
* Induction hardened rolls
* Fully welded steel (St -52 frame)
* Dual bending speed
* Hydraulic open and close operated from control panel
* Top and Bottom (central rolls) driven by hydraulic motor and planetary gear reducer
AKYAPAK: HYDRAULIC AHS ROLLS: 3100 X 6.0MM
SKU:
ROL131265
* 4 Roller Plate bending machine
* Precise pinching of plate between top and bottom rolls.
* Legth of flat ends minimised.
* Cone rolling device
* Induction hardened rolls
* Fully welded steel (St -52 frame)
* Dual bending speed
* Hydraulic open and close operated from control panel
* Top and Bottom (central rolls) driven by hydraulic motor and planetary gear reducer
AKYAPAK: SLIP ROLLS ASM 2050 X 4MM
SKU:
ROL131273
* Body is made of cast-iron construction.
* Rolling driven by electric motor + reducer
* Upper roll is openable by side.
* Lower and back rolls are adjutable up and down with hand wheel.
* Self brake main motor
* Cone rolling device
* Seaparate moveable control panel and foot pedal
* Suitable for CE standard.
AKYAPAK: SLIP ROLLS ASM 1300 X 6.5MM
SKU:
ROL131277
* Body is made of cast-iron construction.
* Rolling driven by electric motor + reducer
* Upper roll is openable by side.
* Lower and back rolls are adjutable up and down with hand wheel.
* Self brake main motor
* Cone rolling device
* Seaparate moveable control panel and foot pedal
* Suitable for CE standard.
AKYAPAK: SLIP ROLLS 2100MM X 6.0MM 2.2KW
SKU:
ROL131300
SLIP ROLLS: 3000 X 10.0MM BENZEL
SKU:
ROL131490
* Two rolls powered by gearbox and gear system
* Swing out end enables complete cylinder to be removed
* Heavy duty steel welded main frames
* Mobile control panel with foot pedals
* Precision ground rolls with wiring grooves
* Safety wire interlock system with emergency shut-off
* Motorised up & down top roll for curving adjustment
ER INITAL PINCH ROLING MACHINE: 2000 X 4.0MM
SKU:
ROL131502
* Initial pinch rolls with pre-bending
* Motorised up & down rear curving roll enables quick & easy pre-bending
* Digital readout display on rear curving roll position
* Mobile foot pedal control with digital readout display
* Two rolls are powered by reduction gearbox drive system
* Swing out top roller enables cone or cylinder to be removed
* Safety wire interlock system with emergency shut-off
* Rolls include wiring grooves
SLIP ROLLS: 2500MM X 12.0MM BENZEL
SKU:
ROL132000
* Two rolls powered by gearbox and gear system
* Swing out end enables complete cylinder to be removed
* Heavy duty steel welded main frames
* Mobile control panel with foot pedals
* Precision ground rolls with wiring grooves
* Safety wire interlock system with emergency shut-off
* Motorised up & down top roll for curving adjustment
* Includes Section roll system with flat bar and pipe dies
* Mild steel capacity is rated on hot rolled material with 250MPA