- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
POWER ROTARY TABLE: 10″ LIBO
$2,875.00
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1’min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
* Controller has three wires, one of them is for powercord conected to DC 24W – 48V. Motor should be conected to 4 pin aviation socket and motor encoder should be connected to the 6 pin aviation conector
| Weight | 38 kg |
|---|---|
| Dimensions | 0.39 × 0.36 × 0.2 cm |
Description
| DESCRIPTION | Power Rotary Table 10″ |
|---|---|
| TYPE | Rotary Table |
| TABLE HEIGHT HORIZONTAL | 110mm |
| HEIGHT VERTICAL | 328mm |
| T-SLOT SIZE | 14.0mm |
| CONTROLLER | Portable Set With Screen |
| VOLTAGE | 24v |
| TORQUE | 4.5nm |
| WEIGHT NETT/GROSS | 32.0/38.0kg |
| VOLUME | 0.0281cm |
| PACKING SIZE L X W X H | 390 x 360 x 200mm |
Shipping & Delivery
Related products
ROTARY TABLE: HV-4 4″ ALTO TILTING
SKU:
RT-9580002A
* This 4" Tilting rotary table is a very versitile unit
* Tilting range is 0 - 90 Degrees with positive locking
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with tee slots in table
* Can be bolted in verticle or horizontal position
ROTARY TABLE: HV-4 4″ ALTO WITH 100MM 3 JAW CHUCK
SKU:
RT-9580003
* This 4" rotary table is a very versitile unit
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with 3 tee slots in table
* This rotary table comes with 100mm 3 jaw chuck in seperate package
* Chuck is on backing plate and can be removed
ROTARY TABLE: HV 16 16″ VERTEX
SKU:
RT-9580016
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1' min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
ROTARY CROSS TABLE: 225 x 175MM LIBO HORZ/VERTICAL
SKU:
RT-9580200
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
TILTING ROTARY TABLE: TSK-200 8″
SKU:
RT-9581003
DIVIDING PLATES: HV-8,” DP-2
SKU:
RT-9581008
DIVIDING PLATES: HV12-14″ OLD TYPE
SKU:
RT-9581012
DIVIDING PLATES: DP-3
SKU:
RT-9581013