- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
LATHE TOOL HOLDER: MTENN 5032-S22 32.0 X 32.0MM
$250.00
Characteristics: * Profiling toolholder with triangular negative double side insert (angle 60 Degrees) with strong cutting edge * The clamp fixing ensures good rigidity and stability in roughing applications*
Applications: * Profiling toolholder for general applications, roughing semi-finishing and finishing *
| Weight | 2.95 kg |
|---|---|
| Dimensions | 0.14 × 0.04 × 0.04 cm |
Related products
LATHE TOOL HOLDER: MTJNR 2525 M16-KN 25.0 X 25.0MM
SKU:
LTH610128
Characteristics: * Turning and profiling toolholder equipped with triangular negative double side insert with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications * Applications * External turning and profiling toolholder for general applications, roughing, semi roughing, and finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 2525M08 25.0 X 25.0MM CANELA
SKU:
LTH610148
Characteristics: * Multipurpose toolholder equipped with trigon negative double side insert (angle 80 Degrees) with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning toolholder for general applications, roughing, semi roughing, semi-finishing and finishing * Not suitable for cermet, ceramic and K10, P10 grade inserts ** This is a 95deg right hand lathe toolholder - takes WNMG0804 inserts ** Right hand lathe tool holder - tip supplied *
LATHE TOOL HOLDER: PRSNL 2020K-M12 20.0 X 20.0MM HARTINGEN
SKU:
LTH610153
Characteristics:
* Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges
Applications:
* External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing
* for Low powered machines and small pieces choose toolholder
LATHE TOOL HOLDER: PSSNR 2525K-M12 25.0 X 25.0MM HARTINGEN
SKU:
LTH610154
Characteristics: * Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges *
Applications: * External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing * for Low powered machines and small pieces choose toolholder Ref CSSP *
LATHE TOOL HOLDER: SCLCL 1212 F09 12.0 X 12.0MM
SKU:
LTH610160
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: SCLCL 1616-H09 16.0 X 16.0MM
SKU:
LTH610166
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: 12.0MM SHANK R/HAND CANALA
SKU:
LTH624070
Characteristics: * Toolholder for external turning applications equipped with trangular positive inserts and strong cutting edges. The top clamp ensures good rigidity and stability.
Applications: * External turning toolholder fo all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder REF PTGN *
LATHE TOOL HOLDER: STGCR 1616-H11 16.0 X 16.0MM
SKU:
LTH700640