- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
LATHE TOOL HOLDER: SCLCR 0808 8 X 8MM
$85.73
| Weight | 0.06 kg |
|---|---|
| Dimensions | 0.12 × 0.03 × 0.03 cm |
In stock
Related products
LATHE TOOL HOLDER: MTJNL 2525M16-KN 25.0 X 25.0MM
SKU:
LTH610124
Characteristics: * Turning and profiling toolholder equipped with triangular negative double side insert with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning and profiling toolholder for general applications, roughing, semi roughing, and finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 1616-H06 16.0 X 16.0MM
SKU:
LTH610140
Characteristics: * Multipurpose toolholder equipped with trigon negative double side insert (angle 80 Degrees) with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning toolholder for general applications, roughing, semi roughing, semi-finishing and finishing * Not suitable for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: PSSNL 2525K-M12 25.0 X 25.0MM HARTINGEN
SKU:
LTH610154L
Characteristics: * Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges *
Applications: * External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing * for Low powered machines and small pieces choose toolholder Ref CSSP *
LATHE TOOL HOLDER: SCLCL 1616-H09 16.0 X 16.0MM
SKU:
LTH610166
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: 16.0MM SHANK L/HAND CANELA
SKU:
LTH624090
Characteristics: * Toolholder for external turning applications equipped with trangular positive inserts and strong cutting edges. The top clamp ensures good rigidity and stability.
Applications: * External turning toolholder fo all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder REF PTGN *
LATHE TOOL HOLDER: CTGPL 2020 K-16 20.0 X 20.0MM
SKU:
LTH624120
Characteristics: * Toolholder for external turning applications equipped with trangular positive inserts and strong cutting edges. The top clamp ensures good rigidity and stability.
Applications: * External turning toolholder fo all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder REF PTGN *
LATHE TOOL HOLDER: CTGPR 2525 M-22 25.0 X 25.0MM
SKU:
LTH624138
Characteristics: * Toolholder for external turning applications equipped with trangular positive inserts and strong cutting edges. The top clamp ensures good rigidity and stability.
Applications: * External turning toolholder fo all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder REF PTGN *
LATHE TOOL HOLDER: CTFPR 1616 H-11 16.0 X 16.0MM
SKU:
LTH624400
Characteristics: * Toolholder for face turning applications equipped with triangular4 positive inserts and strong cutting edges * The top clamp ensures good rigidity and stability *
Applications: * Face turning toolholder for all kinds of materials * The workpiece should be stable *
* For interrupted cut choose toolholder Ref PTFN *