- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
LATHE TOOL HOLDER: CTFPR 2020-K16 20.0 X 20.0MM
$114.74
Characteristics: * Toolholder for face turning applications equipped with triangular positive inserts and strong cutting edges * The top clamp ensures good rigidity and stability*
Applications: * Face turning toolholder for all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder PTFN *
| Weight | 0.42 kg |
|---|---|
| Dimensions | 0.14 × 0.03 × 0.03 cm |
In stock
Related products
LATHE TOOL HOLDER: MTJNL 2525M16-KN 25.0 X 25.0MM
SKU:
LTH610124
Characteristics: * Turning and profiling toolholder equipped with triangular negative double side insert with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning and profiling toolholder for general applications, roughing, semi roughing, and finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 2020 K06 20/.0 X 20.0MM
SKU:
LTH610132
Characteristic: * Multi purpose holder with trigon neg. double sided insert with strong cutting edge. The centre pin and top clamp ensure good rigidity and stability in roughing applications. Suitable general applications roughing to finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 1616-H06 16.0 X 16.0MM
SKU:
LTH610140
Characteristics: * Multipurpose toolholder equipped with trigon negative double side insert (angle 80 Degrees) with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning toolholder for general applications, roughing, semi roughing, semi-finishing and finishing * Not suitable for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 2020-K08 20.0 X 20.0MM
SKU:
LTH610144
Characteristics: * Multipurpose toolholder equipped with trigon negative double side insert (angle 80 Degrees) with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning toolholder for general applications, roughing, semi roughing, semi-finishing and finishing * Not suitable for cermet, ceramic and K10, P10 grade inserts ** This is a 95deg right hand lathe toolholder - takes WNMG0804 inserts *
LATHE TOOL HOLDER: PRSNL 2020K-M12 20.0 X 20.0MM HARTINGEN
SKU:
LTH610153
Characteristics:
* Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges
Applications:
* External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing
* for Low powered machines and small pieces choose toolholder
LATHE TOOL HOLDER: SCLCL 1010-E06 10.0 X 10.0MM
SKU:
LTH610156
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: SCLCR 1010-M06 10.0 X 10.0MM
SKU:
LTH610170
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: 12.0MM SHANK R/HAND CANALA
SKU:
LTH624070
Characteristics: * Toolholder for external turning applications equipped with trangular positive inserts and strong cutting edges. The top clamp ensures good rigidity and stability.
Applications: * External turning toolholder fo all kind of materials * The workpiece should be stable * For interrupted cut choose toolholder REF PTGN *