- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
LATHE TOOL HOLDER: MTJNR 2525 M16-KN 25.0 X 25.0MM
$145.00
Characteristics: * Turning and profiling toolholder equipped with triangular negative double side insert with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications * Applications * External turning and profiling toolholder for general applications, roughing, semi roughing, and finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
| Weight | 0.715 kg |
|---|---|
| Dimensions | 0.16 × 0.03 × 0.03 cm |
In stock
Related products
LATHE TOOL HOLDER: MTJNL 2525M16-KN 25.0 X 25.0MM
SKU:
LTH610124
Characteristics: * Turning and profiling toolholder equipped with triangular negative double side insert with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning and profiling toolholder for general applications, roughing, semi roughing, and finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNR 2020 K06
SKU:
LTH610132
Characteristic: * Multi purpose holder with trigon neg. double sided insert with strong cutting edge. The centre pin and top clamp ensure good rigidity and stability in roughing applications. Suitable general applications roughing to finishing * Specially recommended for cermet, ceramic and K10, P10 grade inserts *
LATHE TOOL HOLDER: MWLNL 2525-M06
SKU:
LTH610136
LATHE TOOL HOLDER: MWLNR 2020-K08 20.0 X 20.0MM
SKU:
LTH610144
Characteristics: * Multipurpose toolholder equipped with trigon negative double side insert (angle 80 Degrees) with strong cutting edge * The centre pin and top clamp ensure good rigidity and stability in roughing applications *
Applications: * External turning toolholder for general applications, roughing, semi roughing, semi-finishing and finishing * Not suitable for cermet, ceramic and K10, P10 grade inserts ** This is a 95deg right hand lathe toolholder - takes WNMG0804 inserts *
LATHE TOOL HOLDER: PSSNR 2525K-M12 HARTINGEN
SKU:
LTH610154
Characteristics: * Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges *
Applications: * External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing * for Low powered machines and small pieces choose toolholder Ref CSSP *
LATHE TOOL HOLDER: PSSNL 2525K-M12 HARTINGEN
SKU:
LTH610154L
Characteristics: * Toolholder for external turning and chamfering applications equipped with square negative inserts and strong cutting edges *
Applications: * External turning and chamfering toolholder for general applications, roughing, semi-finishing and finishing * for Low powered machines and small pieces choose toolholder Ref CSSP *
LATHE TOOL HOLDER: SCLCL 2020-K09
SKU:
LTH610168
Characteristics: * Multipurpose toolholder equipped with rhombic positive insert (angle 80 degrees) * The centre screw ensures good rigidity and chip flow *
Applications: * External turning toolholder for general applications, roughing, semi-finishing and finishing * Negative inserts toolholders Ref MCLN-K or MCLN or PCLN *
LATHE TOOL HOLDER: STGCR 1616-H11 16.0 X 16.0MM
SKU:
LTH700640