- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
DIVIDING PLATES: DP1 HV-4/6″ ALTO
$120.00
* Will fit 6 Vertex rotary tables by removing handwheel *
| Weight | 3.5 kg |
|---|---|
| Dimensions | 0.2 × 0.22 × 0.06 cm |
In stock
Related products
ROTARY TABLE: HV-3 3″ ALTO W/CHUCK
SKU:
RT-9580001A
ROTARY TABLE: HV-4 4″ ALTO WITH 100MM 3 JAW CHUCK
SKU:
RT-9580003
* This 4" rotary table is a very versitile unit
* Table diameter is 100mm
* Worm gear ratio 1:36 = 1 rotation will increase by 10 degrees
* Graduated indexing dial to 360 derees
* Centre height in verticle = 66.0mm approx
Hand wheel is graduated in 10 min divisions and can be set at zero
* Comes with 3 tee slots in table
* This rotary table comes with 100mm 3 jaw chuck in seperate package
* Chuck is on backing plate and can be removed
ROTARY CROSS TABLE: 225 x 175MM LIBO HORZ/VERTICAL
SKU:
RT-9580200
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
ROTARY CROSS TABLE: 330 X 220MM LIBO
SKU:
RT-9580205
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting borin
ROTARY CROSS TABLE: 425 X 240MM LIBO
SKU:
RT-9580210
* Table is made from high density Meehanite casting with ground finish
* Tested by Heidenhain electronic testing equipment to ensure the utmost quality
* Spindle end is supported by taper roller bearings to ensure stablity under cutting conditions
* Worm is hardened and ground and has a ratio of 90:1
* The worktable is graduated to the full 360ø so that one turn of the handle moves the table through 4ø
* Micro collar is graduated in steps of 1'min and vernier scale makes settings down to 10 seconds possible
* These rotary tables are popular for their excellent performance practical design and affordable cost
* Widely used for circular cutting work angle setting boring
DIVIDING PLATES: HV-8,” DP-2
SKU:
RT-9581008
TAILSTOCK: TS-4
SKU:
RT-9581056
TAILSTOCK: TS-1 SUIT 3″ TO 6″ CENTRE HEIGHT (LIBO)
SKU:
RT-9581060