- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
END MILL: 8.0MM HSS-Co8 STD THREADED SHANK (SOMTA)
Excl. GST: $35.00
Incl. GST: $40.25
Incl. GST: $40.25
END MILL: 9.0MM HSS-Co8 STD (SOMTA) FLAT SHANK
Excl. GST: $39.00
Incl. GST: $44.85
Incl. GST: $44.85
END MILL: 8.0MM HSS-Co8 STD
Excl. GST: $14.73
Incl. GST: $16.94
* This End Mill is a standard series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
| Weight | 0.19 kg |
|---|---|
| Dimensions | 0.1 × 0.03 × 0.03 cm |
In stock
Related products
END MILL: HSS 11.0MM STD THR/SHANK GSE
SKU:
EM-700432
END MILL: HSS 14.0MM STD THR/SHANK GSE
SKU:
EM-700444
END MILL: HSS 15.0MM STD THR/SHANK GSE
SKU:
EM-700448
END MILL: HSS 16.0MM STD THR/SHANK GSE
SKU:
EM-700452
END MILL: 4.0MM HSS-Co8 4 FLUTE LONG SERIES T/SHANK (SOMTA)
SKU:
EM-74210204
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 5.0MMHSS-Co8 4 FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210205
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 13.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210213
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 18.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210218
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *