- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
PIPE CENTRE: MT2 X 2-1/2″
$168.00
* The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8″ )
| Weight | 0.6 kg |
|---|---|
| Dimensions | 0.2 × 0.1 × 0.1 cm |
In stock
Related products
PIPE CENTRE: MT2 X 3″
SKU:
PCL9136028
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT2 X 4″
SKU:
PCL9136030
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT3 X 2-1/2″
SKU:
PCL9136031
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT4 X 3″
SKU:
PCL9136042
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT4 X 5″
SKU:
PCL9136045
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT5 X 6″
SKU:
PCL9136056
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT5 X 8″
SKU:
PCL9136058
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm ( 2-1/2-8" )
PIPE CENTRE: MT5 X 10″
SKU:
PCL9136062
The pipe centre is designed hold hollow workpieces between centres in a lathe
* Various head diameters and morse tapers are available depending on the hole of the workpiece you wish to hold
* All head are supplied with ball and taper roller bearing to provide smooth running and reliability at all times
* Center is made from alloy steel and is waterproof design
* Concentricity tolerence is +_ 0.005mm