- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
END MILL: HSS 16.0MM STD
$33.40
* These End Mill are a Standard general purpose cutter
* 4 Flutes, Single End, Square End Style, Center Cutting Type
* Right Hand Cut HSS-M2
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg
* Suitable for Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speed
| Weight | 0.13 kg |
|---|---|
| Dimensions | 0.1 × 0.03 × 0.03 cm |
In stock
Related products
END MILL: HSS 11.0MM STD
SKU:
EM-700432
END MILL: HSS 19.0MM STD
SKU:
EM-700464
END MILL: HSS 11/32″ STD
SKU:
EM-700630
END MILL: 3.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210200
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 5.0MMHSS-Co8 4 FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210205
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 10.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210210
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 11.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210211
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 13.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210213
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *