- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
Back in Stock Soon
END MILL: 8.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
$38.00
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
| Weight | 0.05 kg |
|---|---|
| Dimensions | 0.1 × 0.03 × 0.03 cm |
Related products
END MILL: HSS 4.0MM STD (SOMTA)
SKU:
EM-700404
END MILL: HSS 5.0MM STD COATED (SOMTA)
SKU:
EM-700408
END MILL: HSS 16.0MM STD
SKU:
EM-700452
END MILL: HSS 17.0MM STD
SKU:
EM-700456
END MILL: 6.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210206
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 12.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210212
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 14.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210214
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *
END MILL: 18.0MM HSS-Co8 4FLUTE LONG-SERIES T/SHANK (SOMTA)
SKU:
EM-74210218
* These threaded shank End Mill are Long series General Purpose, 4 Flutes, Single End, Square End Style, Center Cutting Type, Right Hand Cut, HSS-M42 (8% Cobalt) ,
* Bright Finish, Rhc 30 Deg, Rhh 30 Deg, For Plunge Cutting, Peripheral Milling and Deep Slotting and Pocketing at Higher Feed and Speeds *