- Show All
- AUTO RECONDITIONING MACHINES
- AXLE STANDS
- BATTERY CHARGERS
- ENGINE STANDS
- GREASE & OILS
- HYDRAULIC BODY JACKS
- HYDRAULIC BOTTLE JACKS
- HYDRAULIC TOE JACKS
- HYDRAULIC TROLLEY JACKS
- HYD ENGINE CRANES
- HYD MOTORCYCLE LIFT
- HYD TRANSMISSION JACKS
- HYD SPRING COMPRESSOR
- HYD VEHICLE POSITIONING JACK
- GARAGE ESSENTIALS
- OIL DRAIN TANK
- PANEL BEATING EQUIPMENT
- WORKSHOP PRESSES
TAP: BSPT 1" X 11 INTER HAND TAP (SOMTA)
Excl. GST: $194.00
Incl. GST: $223.10
Incl. GST: $223.10
TAP: NPT 1/8" X 27 BOTTOM
Excl. GST: $46.52
Incl. GST: $53.50
Incl. GST: $53.50
TAP: NPT 1/8″ X 27 TAPER
Excl. GST: $46.52
Incl. GST: $53.50
* These NPT pipe taps are manufactured from quality HSS-M2 for durability and long service life *
| Weight | 0.05 kg |
|---|---|
| Dimensions | 0.12 × 0.03 × 0.03 cm |
In stock
Related products
TAP SET: 3PC M3.0 X 0.35 HSS-M2 METRIC FINE
SKU:
TAP3161203
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP SET: 3PC M12.0 X 1.25 HSS-M2 METRIC FINE (SPARK PLUG)
SKU:
TAP3161210
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP SET: 3PC M12.0 X 1.50 HSS-M2 METRIC FINE
SKU:
TAP3161212
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP SET: 3PC M18.0 X 1.5 HSS-M2 METRIC FINE (SPARK PLUG)
SKU:
TAP3161218
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP SET: 3PC M22.0 X 1.5 HSS-M2 METRIC FINE
SKU:
TAP3161222
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP SET: 3PC M32.0 X 1.5 HSS-M2 METRIC FINE (CONDUIT)
SKU:
TAP3161232
* All our taps are manufactured from quality HSS-M2 for durability and extended tool life * These 3pc sets consist of: Taper, Intermediate and botton taps
* Taper or first tap has a long chamfer and trapeziform cutting edges and preformd about 60% of the cutting work
* The intermediate or second tap has a shorter chamfer and trapeziform cutting edgeswhich are deeper, and completes around 30% of the cutting work
* The 3rd or bottoming tap (finishing) has a short chamfer and cutting edgeswhich create the final sharp form of the thread groove
TAP: NPT 1/4″ X 18 TAPER
SKU:
TAP3346015
TAP: NPT 1/2″ X 14 TAPER
SKU:
TAP3346025